There are two situations:
1. The LM3S8962 development board uses another emulator instead of the built-in emulator1. If it is the EK-LM3S8962-A version of the board, first you need to add a 0Ω resisto...
[size=12px]The most complete reference material on stepper motors, classic edition[/size] [[i] This post was last edited by fqegeeer on 2009-8-10 15:00[/i]]...
Hello everyone, I am a young technician who has just stepped out of school. I would like to ask you some questions. I want to use DA14580 to make a device with a thin film pressure sensor. I have the ...
[b]A Solution Concept[/b] When using MCU to control BLDC motor, a three-phase H-bridge drive circuit must be made for BLDC, and then 6-way PWM and H-bridge connection are generated through isolation. ...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
On April 17, the U.S. Department of Commerce suddenly announced that it would completely ban U.S. companies from
selling parts, goods, software and technology
to
ZTE
within 7 years. This als...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
Recently, the "Smart Photovoltaic Industry Development Action Plan (2018-2020)" jointly issued by six departments has put this concept on the forefront. Photovoltaic smart solutions will become the ne...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
I believe that many netizens who have watched "Interstellar" will remember this classic line, "Do not go gentle into this good night, nor let passion be drowned by the gloom of twilight". Different...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
ADC: 1. The ADC module inside STM32 has three ADC1, ADC2, and ADC3, which are independent of each other, so synchronous sampling can be performed. 2ADC input clock must not exceed 14MHz, it is genera...[Details]
The frequency calculation formula of the PWM wave generated by the output comparison mode of the timer is: 72M/((2*(arr+1))*(psc+1) ) For example, if you set: PWM_Init(1000-1,72-1); (PWM_Init(arr,psc...[Details]
T1 or T2 are two timers/counters of MCS-51 microcontroller. The first method can use two timers/counters to generate rectangular waves. In order to save interface resources, the second method is used...[Details]
The single-chip microcomputer running light program requires all 32 serial ports to be used, and each serial port has eight LEDs. Question supplement: The 8051 single-chip microcomputer is used, an...[Details]
A simple experimental programming question for the microcontroller: write a 3-byte binary addition subroutine. The program entry is: addend 1: 22H, 21H, 20H three bytes, 22H is the highest bit; adden...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
