EEWORLDEEWORLDEEWORLD

Part Number

Search

LT1039AC

Description
Triple RS232 Driver/Receiver with Shutdown
File Size223KB,12 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet Compare View All

LT1039AC Overview

Triple RS232 Driver/Receiver with Shutdown

LT1039A/LT1039A-16
Triple RS232 Driver/Receiver
with Shutdown
FEATURES
s
DESCRIPTION
The LT
®
1039A is a triple RS232 driver/receiver that
includes shutdown. Each receiver will accept up to
±30V
input and can drive either TTL or CMOS logic. The RS232
drivers accept TTL logic inputs and output RS232 voltage
levels. The outputs are fully protected against overload
and can be shorted to ground or up to
±30V
without
damage to the drivers. Additionally, when the system is
shut down or power is off, the outputs are in a high
impedance state allowing data line sharing. On-chip ESD
protection eliminates the need for external protection
devices.
A bias pin allows one receiver to be kept on while the rest
of the part is shut down.
The LT1039A is also available in the 16-pin version,
without shutdown or bias pin functions.
For applications requiring operation from a single 5V
supply, see the LT1180A/LT1181A and LT1130A data
sheets.
, LTC and LT are registered trademarks of Linear Technology Corporation.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
On-Chip ESD Protection:
±15kV
Human Body Model
±15kV
IEC-1000-4-2 Air Gap Test**
±8kV
IEC-1000-4-2 Contact Test
125kBd Operation with 3kΩ/2500pF Load
250kBd Operation with 3kΩ/1000pF Load
Operates from
±5V
to
±15V
Supplies
Fully Protected Against Overload
Outputs Can Be Driven
±30V
Without Damage
Three-State Outputs; Outputs Open When Off
Bipolar Circuit—No Latchup
±30V
Input Range
Triple Driver/Receiver
No Supply Current in Shutdown
30kΩ Input Impedance
Meets All RS232 Specifications
16-Pin Version—Pin Compatible with MC145406
Available in SO Package
APPLICATIONS
s
s
s
RS232 Interface
Terminals
Modems
TYPICAL APPLICATION
12V
BIAS*
RS232 IN
50Ω**
RS232 OUT
RS232 IN
*BIAS PIN USED
50Ω**
TO KEEP THE
RS232 OUT
RECEIVER ON
WHILE IN SHUTDOWN
RS232 IN
**50Ω RESISTORS
MAY BE REQUIRED
50Ω**
FOR IEC-1000-4-2
RS232 OUT
ESD PROTECTION
DEPENDING UPON
– 12V
PC BOARD AND
CONNECTOR LEAD LENGTH
1
2
3
30k
4
5
30k
6
7
30k
8
9
V
V
+
LT1039A
V
CC
18
17
16
5V
ON/OFF
LOGIC
Driver Output Swing
OUTPUT VOLTAGE REFERRED TO SUPPLIES (V)
V
+
– 0.4
– 0.8
–1.2
–1.6
– 2.0
15
14
LOGIC
LOGIC
13
12
LOGIC
LOGIC
1.2
0.8
0.4
V
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
OUTPUT CURRENT (mA)
1039A TA02
11
GND
1039A TA01
LOGIC
10
U
U
U
1

LT1039AC Related Products

LT1039AC LT1039AMJ16 LT1039AM LT1039AISW16 LT1039AIN16 LT1039AI
Description Triple RS232 Driver/Receiver with Shutdown Triple RS232 Driver/Receiver with Shutdown Triple RS232 Driver/Receiver with Shutdown Triple RS232 Driver/Receiver with Shutdown Triple RS232 Driver/Receiver with Shutdown Triple RS232 Driver/Receiver with Shutdown
Ask a question to the MCU masters
[i=s]This post was last edited by Qiu Fengye Luoshi on 2015-5-30 23:39[/i] The program is written and there is no problem, but an error occurred when debugging the program: Sat May 30, 2015 23:06:01: ...
秋枫叶落时 MCU
About LM3S811J-LINK Emulator
Do I have to buy a J-Link emulator for LM3S811? Can I not download programs to the board without an emulator?...
609408705 Microcontroller MCU
Looking for partners
It's been almost two years since I graduated, but I still haven't found a direction for development. Fortunately, I work in the field of my major. My current location is Harbin. If there are colleague...
zwbs007 Embedded System
Internal combustion engine injection rate measurement equipment
Internal combustion engine spray research requires a set of fuel injection rate measurement equipment, or provides measurement ideas. For example, what sensor to use? What measures to take to measure ...
luo101luo Test/Measurement
[Show samples] + I share with you what I applied for after much hardship
After the release of this event, I was quite interested, especially for the prize [color=#333333][font=微软雅黑] (Jeep Seiko Tool Set), but the application process has not been smooth. [/font][/color] It ...
feg TI Technology Forum
I received the PCB of the LIS3DSH minimum evaluation board, and attached a video of cutting it.
I received the PCB today and took a quick look at it. I didn't make the same mistake as last time. When I sent the board for the second time, I pulled the CS pin that I forgot to connect last time to ...
littleshrimp MEMS sensors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1601  940  2331  2266  553  33  19  47  46  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号