EEWORLDEEWORLDEEWORLD

Part Number

Search

LT1027CCH-5

Description
Precision 5V Reference
CategoryPower/power management    The power supply circuit   
File Size170KB,8 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet Parametric View All

LT1027CCH-5 Overview

Precision 5V Reference

LT1027CCH-5 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerLinear ( ADI )
Parts packaging codeTO-5
package instructionTO-5, CAN8,.2
Contacts8
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresOUTPUT ADJUST RANGE IS +/-0.05V
Analog Integrated Circuits - Other TypesTHREE TERMINAL VOLTAGE REFERENCE
JESD-30 codeO-MBCY-W8
JESD-609 codee0
Number of functions1
Output times1
Number of terminals8
Maximum operating temperature70 °C
Minimum operating temperature
Maximum output voltage5.0025 V
Minimum output voltage4.9975 V
Nominal output voltage5 V
Package body materialMETAL
encapsulated codeTO-5
Encapsulate equivalent codeCAN8,.2
Package shapeROUND
Package formCYLINDRICAL
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
Maximum supply voltage (Vsup)40 V
Minimum supply voltage (Vsup)8 V
Nominal supply voltage (Vsup)10 V
surface mountNO
technologyBIPOLAR
Maximum voltage temperature coefficient3 ppm/°C
Temperature levelCOMMERCIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formWIRE
Terminal locationBOTTOM
Maximum time at peak reflow temperatureNOT SPECIFIED
Fine-tuning/adjustable outputYES
Maximum voltage tolerance0.05%
Base Number Matches1
LT1027
Precision
5V Reference
FEATURES
s
s
DESCRIPTIO
s
s
s
s
s
Very Low Drift: 2ppm/°C Max TC
Pin Compatible with LT1021-5, REF-02,
(TO-5 and PDIP Packages Only)
Output Sources 15mA, Sinks 10mA
Excellent Transient Response Suitable for
A-to-D Reference Inputs
Noise Reduction Pin
Excellent Long Term Stability
Less Than 1ppm
P-P
Noise (0.1Hz to 10Hz)
APPLICATIO S
s
s
s
s
The LT
®
1027 is a precision reference with extra-low drift,
superior accuracy, excellent line and load regulation and
low output impedance at high frequency. This device is
intended for use in 12- to 16-bit A-to-D and D-to-A
systems where demanding accuracy requirements must
be met without the use of power hungry, heated substrate
references. The fast settling output recovers quickly from
load transients such as those presented by A-to-D converter
reference inputs. The LT1027 brings together both
outstanding accuracy and temperature coefficient
specifications.
The LT1027 reference is based on LTC’s proprietary
advanced subsurface Zener bipolar process which
eliminates noise and stability problems associated with
surface breakdown devices.
, LTC and LT are registered trademarks of Linear Technology Corporation.
A-to-D and D-to-A Converters
Digital Voltmeters
Reference Standard
Precision Current Source
TYPICAL APPLICATIO
Supplying V
REF
and V
CC
to the LTC
®
1290 12-bit ADC
Output Voltage
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
COM
REF
+
REF
V
CC
S
CLK
A
CLK
D
OUT
D
IN
CS
OUTPUT VOLTAGE (V)
ANALOG
INPUTS
8V TO 40V
TO
µC
LTC1290
V
IN
+
2.2µF
LT1027
V
OUT
+
V
TRIM
10k
22µF
AGND
V
DGND
GND
1027 TA01
U
5.006
5.004
5.002
5.000
4.998
4.996
4.994
–50
–25
50
25
0
TEMPERATURE (°C)
75
100
1027 TA02
U
U
1
Keyboard mechanism (from Tianyun Technology)
In this section, we will look at the key mechanism. Later, we will look at the UART mechanism and the binding mechanism. Through these three mechanisms, we can deeply study the message transmission me...
王加辉 RF/Wirelessly
Thonny IDE Portable
[i=s]This post was last edited by dcexpert on 2021-5-8 09:20[/i]Thonny is an IDE for beginners, integrating multiple functions such as code editing, file transfer, serial terminal, data visualization,...
dcexpert MicroPython Open Source section
Problems reading and writing fpga registers
I want to read and write 4 registers in FPGA under 2440. The chip select of FPGA is cs4. First, set the timing (PROGRAMMABLE ACCESS CYCLE) and map 0x20000000 to virtual memory. At this time, the physi...
firegao311 Embedded System
f5529 lab4 usb experiment in the experimental board transmits data to the host and receives it using the hyperterminal
There are two important statements in lab4.c: cdcReceiveDataInBuffer(dataBuffer, BUFFER_SIZE, CDC0_INTFNUM); //Receive cdcSendDataInBackground(dataBuffer, bytesReceived,CDC0_INTFNUM, 0); //Send Declar...
白云一片 Microcontroller MCU
How to design a card reader using 51 chip? Can an expert give me the overall design?
As the title says, since this is my first time to design hardware, I am a little confused......
毅通客服1 Embedded System
Discussion on the design of DDS + elliptical low-pass filter with a frequency of 1MHZ
[img=500,148]http://www.amobbs.com/data/attachment/forum/201302/22/132032pr5pnnsjdspex934.jpg.thumb.jpg[/img] Hello everyone: The clock frequency of the AD9833 in the above picture is 20MHZ, and the d...
PSIR Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 208  1430  25  1469  2349  5  29  1  30  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号