LSH32JC32 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > LSH32JC32

Preview

LSH32JC32: Description32-bit Cascadable Barrel Shifter; File Size163KB，9 Pages; ManufacturerLOGIC Devices; Websitehttp://www.logicdevices.com/

Download Datasheet Compare View All

LSH32JC32 Overview

32-bit Cascadable Barrel Shifter

Preview

Download Datasheet

View All

LSH32

DEVICES INCORPORATED

32-bit Cascadable Barrel Shifter

LSH32

DEVICES INCORPORATED

32-bit Cascadable Barrel Shifter

DESCRIPTION

The

LSH32

is a 32-bit high speed

shifter designed for use in floating

point normalization, word pack/

unpack, field extraction, and similar

applications. It has 32 data inputs,

and 16 output lines. Any shift

configuration of the 32 inputs, includ-

ing circular (barrel) shifting, left shifts

with zero fill, and right shift with sign

extend are possible. In addition, a

built-in priority encoder is provided

to aid floating point normalization.

SHIFT ARRAY

The 32 inputs to the LSH32 are

applied to a 32-bit shift array. The 32

outputs of this array are multiplexed

down to 16 lines for presentation at

the device outputs. The array may be

configured such that any contiguous

16-bit field (including wraparound of

the 32 inputs) may be presented to the

output pins under control of the shift

code field (wrap mode). Alterna-

tively, the wrap feature may be

disabled, resulting in zero or sign bit

fill, as appropriate (fill mode). The

shift code control assignments and the

resulting input to output mapping for

the wrap mode are shown in Table 1.

Essentially the LSH32 is configured as

a left shift device. That is, a shift code

of 00000

results in no shift of the

input field. A code of 00001

provides

an effective left shift of 1 position, etc.

When viewed as a right shift, the shift

code corresponds to the two’s com-

plement of the shift distance, i.e., a

shift code of 11111

(–1

) results in a

right shift of one position, etc.

When not in the wrap mode, the

LSH32 fills bit positions for which

there is no corresponding input bit.

The fill value and the positions filled

depend on the RIGHT/LEFT (R/L)

direction pin. This pin is a don’t care

input when in wrap mode. For left

shifts in fill mode, lower bits are filled

with zero as shown in Table 2. For

right shifts, however, the SIGN input

is used as the fill value. Table 3

depicts the bits to be filled as a

function of shift code for the right shift

case. Note that the R/L input changes

only the fill convention, and does not

affect the definition of the shift code.

In fill mode, as in wrap mode, the shift

code input represents the number of

shift positions directly for left shifts,

but the two’s complement of the shift

code results in the equivalent right

shift. However, for fill mode the R/L

input can be viewed as the most

MS/LS

FEATURES

32-bit Input, 32-bit Output Multi-

plexed to 16 Lines

Full 0-31 Position Barrel Shift

Capability

Integral Priority Encoder for 32-bit

Floating Point Normalization

Sign-Magnitude or Two’s Comple-

ment Mantissa Representation

32-bit Linear Shifts with Sign or

Zero Fill

Independent Priority Encoder

Outputs for Block Floating Point

68-pin PLCC, J-Lead

LSH32 B

LOCK

IAGRAM

SIGN I

-I

32:5

PRIORITY

ENCODE

2:1

-SI

RIGHT/LEFT

FILL/WRAP

NORM

32-bit

BARREL

SHIFT

ARRAY

2:1

-SO

-Y

Special Arithmetic Functions

08/16/2000–LDS.32-Q

LSH32JC32 Related Products

	LSH32JC32	LSH32JC20	LSH32
Description	32-bit Cascadable Barrel Shifter	32-bit Cascadable Barrel Shifter	32-bit Cascadable Barrel Shifter

Recommended Resources

Bistable circuit triggered by count input

Three-phase three-wire active energy meter connected to DX1 reactive energy meter

Fluorescent lamp electronic ballast circuit 5

LM2574, LM2574HV application circuit diagram

Square transformation circuit

Computer motherboard circuit diagram 440GX_39

What op amp from TI is used for high frequency small signal amplification: [i=s] This post was last edited by dontium on 2015-1-23 11:35 [/i] The signal amplitude is less than 20mvpp, the frequency is 20MHZ, which TI op amp is better to use as the preamplifier. I have opa690...; sw3926 Analogue and Mixed Signal

I am a newbie and would like some tutorials on wiring in Altium Designer.: I am a newbie and would like some tutorials on wiring in Altium Designer. Thank you....; kunkunchou PCB Design

waveAPI.dll->audio device manager->software mixer: waveAPI.dll->audio device manager->software mixer How do I use this software mixer? How do I find its related information? I can't find it in the help? Do I add some item to sysgen? How do I use the a...; catdud Embedded System

Understanding of msp430f5310 timer: [p=26, null, left][color=rgb(0, 0, 0)]a. There are two types of timers: Timer_A and Timer_B. Timer_A has three timers of the same type, TimerA0, TimerA1 and TimerA2. That is to say, 5310 can provide y...; moshuiilove520 Microcontroller MCU

Various websites: Later, add http://maxiaojia8.blog.163.com/security expert group...; zhouning201 Industrial Control Electronics

MINI2440+uCOSII+uCGUI3.98+X35 screen: I have been tinkering with MINI2440+uCOSII+uCGUI3.98+X35 screen these days. I have consulted many forums on the Internet and tried continuously. Finally, I have figured it out and I would like to shar...; benghopy Real-time operating system RTOS

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components