EEWORLDEEWORLDEEWORLD

Part Number

Search

3GDF8G-D-80T-38.000

Description
LVDS Output Clock Oscillator, 38MHz Nom, ROHS COMPLIANT, DIP-8/4
CategoryPassive components    oscillator   
File Size109KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GDF8G-D-80T-38.000 Overview

LVDS Output Clock Oscillator, 38MHz Nom, ROHS COMPLIANT, DIP-8/4

3GDF8G-D-80T-38.000 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompliant
Maximum control voltage3 V
Minimum control voltage0.3 V
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
frequency stability25%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency38 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
Output load50 OHM
physical size12.8mm x 12.8mm x 5.08mm
longest rise time0.7 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
8 pin Dual-in-Line
Frequency range 38MHz to 640MHz
LVDS Output
Supply Voltage 3.3 VDC
Phase jitter 0.4ps typical
Pull range from ±30ppm to ±150ppm
GDF8 LVDS VCXO
38.0MHz to 640.0MHz
DESCRIPTION
GDF8 VCXOs are packaged in an industry-standard 8 pin dual-in-line
package. Typical phase jitter for GDF series VCXOs is 0.4 ps. Output
is LVDS. Applications include phase lock loop, SONET/ATM, set-top
boxes, MPEG , audio/video modulation, video game consoles and
HDTV.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
RMS Period Jitter:
Peak to Peak Jitter:
Phase Jitter:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Control Voltage Range:
Temperature Stability:
Output Load:
Rise/Fall Times:
Duty Cycle:
Start-up Time:
Current Consumption:
Static Discharge Protection:
Storage Temperature:
Ageing:
Enable/Disable:
RoHS Status:
OUTLINE & DIMENSIONS
38.0MHz to 640.0MHz
3.3 VDC ±5%
LVDS
3.0ps typical
20.0ps typical, 30.0ps maximum
0.4ps typical, 5.0ps maximum
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
1.4 Volts typical
1.1 Volts typical
From ±30ppm to ±150ppm
1.65 ±1.35 Volts
See table
50W into Vdd or Thevenin equiv.
0.5ns typ., 0.7ns max.
20% Vdd to 80% Vdd
50% ±5%
(Measured at Vdd-1.3V)
10ms maximum, 5ms typical
55mA typical, 60mA maximum
(At 202.50MHz)
2kV maximum
-55° to +150°C
±2ppm per year maximum
Not implemented - 4 pin package
Fully compliant or non compliant
PART NUMBERING
Example:
Supply Voltage
3 = +3.3V
Series Designator
GDF8
RoHS Status
G = RoHs compliant
Blank = RoHS non-compliant
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
3GPF8G-B-80N-60.000
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
About soldering
Brothers who work in electronics will come into contact with all kinds of wires, PCB copper foil circuits, chip pins, etc. that need to be soldered, bridged or repaired... How fine is the finest work ...
heyidisk DIY/Open Source Hardware
How is AD converted inside the ez430-RF2500 development board?
Help: How is the internal AD conversion performed in the ez430-RF2500 development board? Why is the data obtained after the sine wave I input is different from the data I calculated after the internal...
yezizi2722 Microcontroller MCU
Power supply technical issues
How many V should the EMC surge of 24V power supply be?...
chilezhima Power technology
How to draw differential serpentine line using AD software?
I saw the option of interactive diff pair length tuning in AD. It should be for differential serpentine line, right? I set it but I can't get it to work. I can't pull out a single line. I can get each...
chen468859 PCB Design
VFS: Cannot open root device "mtdblock2" or unknown-block(0,0)
I have seen many people encounter the following problem on the Internet. Most people speculate the cause of the problem without actually trying it. After I encountered this problem, I tested it myself...
bjwang Linux and Android
MSP430G2553 capacitive touch button programming problem
The official capacitive touch button routine uses a watchdog timer and a TIMER A0 timer. When I add a TIMER A1 timer, I find that it interferes with the touch button and causes misjudgment of the touc...
hjl240 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2044  245  1748  1291  856  42  5  36  26  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号