316-93-122-41-007 datasheet, PDF

Datasheet> All Categories > The connector> socket> 316-93-122-41-007

316-93-122-41-007: DescriptionIC Socket, SIP22, 22 Contact(s); CategoryThe connector socket; File Size169KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com

Download Datasheet Parametric View All

316-93-122-41-007 Overview

IC Socket, SIP22, 22 Contact(s)

316-93-122-41-007 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	Mill-Max
Reach Compliance Code	compliant
ECCN code	EAR99
Other features	SIP SOCKET
Contact to complete cooperation	GOLD (30) OVER NICKEL
Contact completed and terminated	TIN LEAD (200) OVER NICKEL
Contact material	NOT SPECIFIED
Device slot type	IC SOCKET
Type of equipment used	SIP22
Shell material	GLASS FILLED POLYETHYLENE POLYESTER
JESD-609 code	e0
Manufacturer's serial number	316
Number of contacts	22
Base Number Matches	1

Preview

Download Datasheet

View All

SINGLE-IN-LINE SOCKETS

Elevated

Single Row

•

Elevated socket strips are

available in 5 different heights.

316...006 uses pin # 0153-1

316...003 uses pin # 0153-2

316...007 uses pin # 0153-3

316...008 uses pin # 0153-4

316...001 uses pin # 0153-5

•

Hi-Rel, 4-finger BeCu #30 clip

rated at 3 amps. See page 208

for details.

Fig. 1

Series 316

Ordering Information

Series 316...006

Standoff Height = .236

Fig. 1

316-XX-1_ _-41-006

Specify # of pins

Series 316...003

01-64

Standoff Height = .315

Fig. 2

316-XX-1_ _-41-003

Specify # of pins

Series 316...007

01-64

Standoff Height = .402

Fig. 3

316-XX-1_ _-41-007

Specify # of pins

Series 316...008

01-64

Standoff Height = .472

Fig. 4

316-XX-1_ _-41-008

Specify # of pins

Series 316...001

01-64

Standoff Height = .594

Fig. 5

Fig. 4

316-XX-1_ _-41-001

Specify # of pins

01-64

XX= Plating Code

See Below

SPECIFY PLATING CODE XX=

For High Temperature

Insulators Add ‘100’

To End Of

Part Numbers

200µ” Sn/Pb

30µ” Au

Sleeve (Pin)

Fig. 5

Contact (Clip)

w w w. m i l l - m a x . c o m

516-922-6000

Recommended Resources

LT1111 voltage flip mode circuit diagram

Medical thermometer circuit with potential isolation

Double closed-loop speed control system (single-phase bridge rectifier circuit)

DM6043/DM6243 type 3 1/2 digit digital inductance and capacitance meter circuit

IGBT overcurrent protection circuit schematic diagram

845E computer motherboard circuit diagram_42

MP2459 related circuit solution: I recently used MP2459. The datasheet says that the enable pin pull-up is effective. I want to ask what is the role of R4 in the example it gives? Can it be directly connected to R5100k? What is the d...; CcKk Power technology

What is the difference between analog IC design and IC design using VHDL language?: I feel that analog IC design should be to design analog circuits, design op amps, etc., and then build TTL, CMOS, etc. on silicon wafers to make IC chips; but I often see that IC design is to design I...; wn1983 Embedded System

TI Industrial Robots Online Seminar Resource Sharing: Main Agenda of the Seminar 1. Provide a detailed introduction to the definition and classification, system considerations, and module analysis of industrial robots; 2. Count the challenges faced in in...; arui1999 Robotics Development

【Signal processing】：FPGA implements DSP (digital signal processing technology): [[i]This post was last edited by liuceone on 2011-12-10 17:30[/i]]...; liuceone FPGA/CPLD

I need help from forum friends to confirm whether the LCD12864 LCD serial driver using the ST7920 controller can read back the display data?: I have been using the LaunchPad G2553 board to write the LCD12864 display driver in 8-bit parallel mode. Now the functions are almost sufficient, so I want to expand some functions, but I find that th...; bobde163 Microcontroller MCU

Can small and medium-sized chips (40, 74, etc.) be controlled by VCC and GND? If VCC and GND are not added, will the circuit be affected if other pins are added to the circuit?: I want to use serial control for some chips. Can I use vcc and gnd to control them? The signal lines are connected in parallel. I use vcc and gnd to control whether they are connected or not. I think ...; SPEED Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components