5962-9320301M2X datasheet, PDF

Datasheet> All Categories > Analog mixed-signal IC> The signal circuit> 5962-9320301M2X

5962-9320301M2X: DescriptionSingle-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CQCC20, CERAMIC, LCC-20; CategoryAnalog mixed-signal IC The signal circuit; File Size115KB，16 Pages; ManufacturerComlinear Corporation

Download Datasheet Parametric Compare View All

5962-9320301M2X Overview

Single-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CQCC20, CERAMIC, LCC-20

5962-9320301M2X Parametric

Parameter Name	Attribute value
package instruction	CERAMIC, LCC-20
Reach Compliance Code	unknown
Analog Integrated Circuits - Other Types	SINGLE-ENDED MULTIPLEXER
JESD-30 code	S-CQCC-N20
length	8.89 mm
Nominal Negative Supply Voltage (Vsup)	-5.2 V
Number of channels	4
Number of functions	1
Number of terminals	20
Nominal off-state isolation	80 dB
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package body material	CERAMIC, METAL-SEALED COFIRED
encapsulated code	QCCN
Package shape	SQUARE
Package form	CHIP CARRIER
Certification status	Not Qualified
Maximum seat height	1.905 mm
Nominal supply voltage (Vsup)	5 V
surface mount	YES
Maximum disconnect time	8 ns
Maximum connection time	21 ns
technology	BIPOLAR
Temperature level	MILITARY
Terminal form	NO LEAD
Terminal pitch	1.27 mm
Terminal location	QUAD
width	8.89 mm
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Make change to final electrical parameter under TABLE II. In accordance with

N.O.R. 5962-R110-95.

Make change to analog input voltage under paragraph 1.3. In accordance with

N.O.R. 5962-R152-95.

Make change to 2nd harmonic distortion test under TABLE I. Redrawn.

Redraw. Update drawing to current requirements. – drw

DATE (YR-MO-DA)

95-04-14

APPROVED

M. A. Frye

95-06-19

M. A. Frye

97-07-07

10-07-01

R. Monnin

Charles F. Saffle

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Rick Officer

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

Rajesh Pithadia

APPROVED BY

Raymond Monnin

DRAWING APPROVAL DATE

93-10-15

REVISION LEVEL

SIZE

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

MICROCIRCUIT, LINEAR, 4:1 HIGH SPEED,

ANALOG MULTIPLEXER, MONOLITHIC SILICON

AMSC N/A

CAGE CODE

67268

SHEET

1 OF 15

5962-93203

DSCC FORM 2233

APR 97

5962-E366-10

1.3 Absolute maximum ratings. 1/

Positive supply voltage (+V

) ..........................................................................

Negative supply voltage (-V

) .........................................................................

Differential voltage between any two grounds .................................................

Analog input voltage range .............................................................................

Digital input voltage range ..............................................................................

Power dissipation (no load ) ............................................................................

Output short circuit duration (output shorted to GND) ......................................

Junction temperature (T

).................................................................................

Storage temperature range .............................................................................

Lead temperature range (soldering 10 seconds) ............................................

Thermal resistance, junction-to-case (θ

) .......................................................

Thermal resistance, junction-to-ambinet (θ

Case E ..........................................................................................................

Case 2 ..........................................................................................................

1.4 Recommended operating conditions.

Positive supply voltage (+V

) ...........................................................................

Negative supply voltage (-V

) ..........................................................................

Differential voltage between any two grounds..................................................

Analog input voltage range ..............................................................................

input voltage range (TTL Mode) ..................................................................

Select input voltage range (TTL Mode) ............................................................

input voltage range (ECL Mode) .................................................................

Select input voltage range (ECL Mode) ...........................................................

COMP

range .....................................................................................................

Ambient operating temperature range (T

) ......................................................

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 -

MIL-STD-1835 -

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

+5.0 V

-5.2 V

10 mV

±2 V

0 V to +5.0 V

0 V to +3.0 V

0 V to -2.0 V

-2.0 V to 0 V

5 pF to 100 pF

-55°C to +125°C

-0.5 V to +7.0 V

+0.5 V to -7.0 V

200 mV

±3 V

-V

to +V

288 mW

Infinite

+175C

-65C to +150C

+300C

See MIL-STD-1835

75C/W

100C/W

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

(Copies of these documents are available online at

https://assist.daps.dla.mil/quicksearch/

or from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

________

1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the

maximum levels may degrade performance and affect reliability.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-93203

SHEET

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with

MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The

modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for

device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified

herein.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2.

3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the

electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full

ambient operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are defined in table I.

3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be

marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer

has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be

marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be

in accordance with MIL-PRF-38535, appendix A.

3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in

MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.

3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535

listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of

compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see

6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this

drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and

herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.

3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for

device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.

3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2

herein) involving devices acquired to this drawing is required for any change that affects this drawing.

3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the

option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made

available onshore at the option of the reviewer.

3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in

microcircuit group number 58 (see MIL-PRF-38535, appendix A).

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-93203

SHEET

5962-9320301M2X Related Products

	5962-9320301M2X	5962-9320301M2A	5962-9320301MEA	5962-9320301MEX
Description	Single-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CQCC20, CERAMIC, LCC-20	Single-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CQCC20, CERAMIC, LCC-20	Single-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CDIP16, CERAMIC, DIP-16	Single-Ended Multiplexer, 1 Func, 4 Channel, BIPolar, CDIP16, CERAMIC, DIP-16
package instruction	CERAMIC, LCC-20	CERAMIC, LCC-20	CERAMIC, DIP-16	CERAMIC, DIP-16
Reach Compliance Code	unknown	unknown	unknown	unknown
Analog Integrated Circuits - Other Types	SINGLE-ENDED MULTIPLEXER	SINGLE-ENDED MULTIPLEXER	SINGLE-ENDED MULTIPLEXER	SINGLE-ENDED MULTIPLEXER
JESD-30 code	S-CQCC-N20	S-CQCC-N20	R-GDIP-T16	R-GDIP-T16
length	8.89 mm	8.89 mm	19.43 mm	19.43 mm
Nominal Negative Supply Voltage (Vsup)	-5.2 V	-5.2 V	-5.2 V	-5.2 V
Number of channels	4	4	4	4
Number of functions	1	1	1	1
Number of terminals	20	20	16	16
Nominal off-state isolation	80 dB	80 dB	80 dB	80 dB
Maximum operating temperature	125 °C	125 °C	125 °C	125 °C
Minimum operating temperature	-55 °C	-55 °C	-55 °C	-55 °C
Package body material	CERAMIC, METAL-SEALED COFIRED	CERAMIC, METAL-SEALED COFIRED	CERAMIC, GLASS-SEALED	CERAMIC, GLASS-SEALED
encapsulated code	QCCN	QCCN	DIP	DIP
Package shape	SQUARE	SQUARE	RECTANGULAR	RECTANGULAR
Package form	CHIP CARRIER	CHIP CARRIER	IN-LINE	IN-LINE
Certification status	Not Qualified	Not Qualified	Not Qualified	Not Qualified
Maximum seat height	1.905 mm	1.905 mm	5.08 mm	5.08 mm
Nominal supply voltage (Vsup)	5 V	5 V	5 V	5 V
surface mount	YES	YES	NO	NO
Maximum disconnect time	8 ns	8 ns	8 ns	8 ns
Maximum connection time	21 ns	21 ns	21 ns	21 ns
technology	BIPOLAR	BIPOLAR	BIPOLAR	BIPOLAR
Temperature level	MILITARY	MILITARY	MILITARY	MILITARY
Terminal form	NO LEAD	NO LEAD	THROUGH-HOLE	THROUGH-HOLE
Terminal pitch	1.27 mm	1.27 mm	2.54 mm	2.54 mm
Terminal location	QUAD	QUAD	DUAL	DUAL
width	8.89 mm	8.89 mm	7.62 mm	7.62 mm
Base Number Matches	1	1	1	1

Recommended Resources

Refrigerator power outage protector circuit

JX-1 type transistor constant temperature automatic controller circuit

Noiseless lighting/logic interface circuit

Positive and negative 10V reference voltage circuit

Color TV remote control 29

0～30V simple regulated power supply circuit

1.2V output LDO: Everyone really chooses 1.2V LDO for Xilinx FPGA power supply....; xaslm Power technology

How do you import .net CF2.0 into PlatForm's BSP package? I want to compile it directly into the operating system.: How do you import .net CF2.0 into the BSP package of PlatForm? I want to compile it directly into the operating system, and the patch cannot be downloaded. However, the tree control on the right is st...; whplcyz Embedded System

AD9162 Configuration Issues: AD9162 has many registers when configuring, but the datasheet gives a START-UP SEQUENCE when configuring, as shown below. However, some registers that need to be configured are not in this START-UPSEQ...; yangsen7336 FPGA/CPLD

USB cable: Do flat USB cables and round USB cables have the same performance in terms of radiation?...; seek Test/Measurement

Ensure grounding quality through isolation: Ensure grounding quality through isolation By Thomas Kugelstadt, Texas InstrumentsIndustrial communications via fieldbus-transceiver systems often require long transmission lines. Failing to recognize...; 安_然 Analog electronics

MINI USB interface size package set: Students who make boards may need PCB diagrams. I hope everyone will download them....; Eadison Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components