EEWORLDEEWORLDEEWORLD

Part Number

Search

LD1084D2M120

Description
5 V FIXED POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSFM3
CategoryPower/power management    The power supply circuit   
File Size488KB,29 Pages
ManufacturerSTMicroelectronics
Websitehttp://www.st.com/
Download Datasheet Parametric View All

LD1084D2M120 Overview

5 V FIXED POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSFM3

LD1084D2M120 Parametric

Parameter NameAttribute value
MakerSTMicroelectronics
Parts packaging codeD2PAK
package instructionTO-263, SMSIP3H,.55TB
Contacts3
Reach Compliance Codeunknow
ECCN codeEAR99
AdjustabilityFIXED
Maximum drop-back voltage 11.5 V
Nominal dropback voltage 11.3 V
Maximum absolute input voltage30 V
Maximum input voltage30 V
Minimum input voltage13.6 V
JESD-30 codeR-PSSO-G3
length10.2 mm
Maximum grid adjustment rate0.025%
Maximum load regulation0.072%
Number of functions1
Output times1
Number of terminals3
Working temperatureTJ-Max125 °C
Operating temperatureTJ-Mi-40 °C
Maximum output current 15 A
Maximum output voltage 112.24 V
Minimum output voltage 111.76 V
Nominal output voltage 112 V
Package body materialPLASTIC/EPOXY
encapsulated codeTO-263
Encapsulate equivalent codeSMSIP3H,.55TB
Package shapeRECTANGULAR
Package formSMALL OUTLINE
Certification statusNot Qualified
Regulator typeFIXED POSITIVE SINGLE OUTPUT LDO REGULATOR
Maximum seat height4.6 mm
surface mountYES
technologyBIPOLAR
Terminal formGULL WING
Terminal pitch2.54 mm
Terminal locationSINGLE
Maximum voltage tolerance2%
width9.15 mm
LD1084 series
5A Low drop positive voltage regulator adjustable and fixed
Feature summary
Typical dropout 1.3V (at 5A)
Three terminal adjustable or fixed output
voltage 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V,
5V, 8V, 9V, 12V.
Guaranteed output current up to 5A
Output tolerance ±1% at 25°C and ±2% in full
temperature range
Internal power and thermal limit
Wide operating temperature range -40°C to
125°C
Package available: TO-220,
D
2
PAK,
D
2
PAK/A
TO-220
D
2
PAK
D
2
PAK/A
Pinout compatibility with standard adjustable
VREG
Description
The LD1084 is a LOW DROP Voltage Regulator
able to provide up to 5A of Output Current.
Dropout is guaranteed at a maximum of 1.5V at
the maximum output current, decreasing at lower
loads. The LD1084 is pin to pin compatible with
the older 3-terminal adjustable regulators, but has
better performances in term of drop and output
tolerance.
A 2.85V output version is suitable for SCSI-2
active termination. Unlike PNP regulators, where
a part of the output current is wasted as quiescent
current, the LD1084 quiescent current flows into
the load, so increase efficiency. Only a 10µF
minimum capacitor is need for stability.
The device is supplied in TO-220, D
2
PAK and
D
2
PAK/A. On chip trimming allows the regulator to
reach a very tight output voltage tolerance, within
±1% at 25°C.
Schematic diagram
April 2007
Rev. 6
1/29
www.st.com
29
Eat mushrooms and see villains! It's the time of the year again when Yunnan people poison themselves
Because of the COVID-19 pandemic, I believe that everyone hasn't traveled for a long time. I'm sharing an article about eating mushrooms in Yunnan to experience the local customs and practices of diff...
eric_wang Talking
Getting Started with Modelsim
...
至芯科技FPGA大牛 FPGA/CPLD
Crosstalk Elimination Technology in Altium Designer
By Jane Zhang , Aug 27, 2019Remember when you were in school and the teacher asked the whole class a question and you knew the answer! You and a few other students excitedly raised your hands, hoping ...
qwqwqw2088 PCB Design
【Week 0】Hanker | Start the demo
Probably because we are in the same city, I received the M4 development board for trial today.The lighting is not good, so just make do with it. I must say that the workmanship is very good and the bo...
zca123 Microcontroller MCU
Problem analysis, everyone's enthusiastic advice, common improvement
Write the following code in quartus: module test(go,out); input go; output out; wire out; reg out1; assign out=out1; always @(negedge go) begin out1=1'b1; #10 out1=1'b0; end endmodule Then create a ne...
eeleader FPGA/CPLD
Nanjing AOSMITH is recruiting sensor engineers
[color=#ff0000][b]1.[font=宋体][size=12.0pt]Sensor Engineer - Software[/size][/font][/b][/color][font=宋体][size=12.0pt] [/size][/font] [font=宋体][size=12.0pt]Job Description: 1. Find and develop air purif...
MythKONG Recruitment

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 647  1402  1859  527  2384  14  29  38  11  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号