EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-02-1070-D

Description
Resistor Networks & Arrays
CategoryPassive components   
File Size351KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBC-T0303AS-02-1070-D Online Shopping

Suppliers Part Number Price MOQ In stock  
WBC-T0303AS-02-1070-D - - View Buy Now

WBC-T0303AS-02-1070-D Overview

Resistor Networks & Arrays

WBC-T0303AS-02-1070-D Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerTT Electronics plc
Product CategoryResistor Networks & Arrays
Resistors
Wire Bondable
WBC Series
Chip Resistors
Wire Bondable
Chip Resistors
Discrete or tapped schematics
MIL inspection available
WBC Series
High resistor density
Discrete or tapped schematics
MIL inspection available
High resistor density
All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2)
IRC’s WBC series wire bondable chip resistors are ideally suited for the most demanding hybrid application.
The WBC combines IRC’s TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to
produce an extremely small tantalum nitride thin film technology with silicon substrate processing to produce
an extremely small footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
( 0 . 5 0 8 mm ± 0 . 0 2 5 )
0. 020˝ ± 0. 001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
1
( 0 . 5 0 8 mm ± 0 . 0 2 5 )
0. 020˝ ± 0. 001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
1
R0202 and
T0303
B0202
1
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
( 0 . 7 6 2 mm ± 0 . 0 2 5 )
0. 030˝ ± 0. 001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
Note 1: Not recommended for new designs
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
BI Technologies IRC Welwyn
http://www.ttelectronics.com/resistors
WBC Series Issue January 2009 Sheet 1 of 3
© TT Electronics plc
05.17
[National Technology N32G457 Review] 4. Serial port 2 DMA interrupt reception and transmission
[i=s]This post was last edited by lugl4313820 on 2022-1-23 22:36[/i]Since the rt_thread serial port is used by finsh by default, the test here uses serial port 2:Open "DS_N32G457 Series Data Manual V1...
lugl4313820 Domestic Chip Exchange
Who in the forum has done physical layer development for GSM or trunking communications?
It is best to understand the agreement or have more than 2 years of experience...
flyingdsp Talking about work
I have a problem with the current signal being conducted by an analog switch or relay. Please advise me.
I have a problem with the current signal being conducted by an analog switch or relay. Please advise me. 1. If it is an analog switch, the leakage current cannot be constant and will change with the s...
shzps Analog electronics
It's urgent, which one should I click???? Reason
ORG 0000H AJMP START ORG 30H START: MOV R1,#01H MOV P1,#0FFH ; Turn off the light MOV TMOD,#00000001B ;Timer/Counter 0 works in mode 1 MOV TH0,#15H MOV TL0,#0A0H; the number is 5536 SETB TR0 ;Timer/Co...
硬制合金 MCU
When a person gets an electric shock, is the current more harmful or the voltage more harmful?
We may have heard the saying "It's not the voltage that kills you, it's the current". But according to Ohm's law, it seems that voltage (V) determines current (I), so the two seem to play the same rol...
tiankai001 Analog electronics
Requesting C2000 Launchpad specifications
Now I don't have lauchpad with me, and I need corresponding parameters to draw PCB. It would be best if there is some document or something. I used to measure it with a vernier caliper, but I didn't b...
550507666 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 97  2652  2048  1742  1414  2  54  42  36  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号