The assembly of 3M Ribbon Cable Sockets, Series 451 .05" x .05" sockets and 3M
™
Flat Ribbon
Cable .025" can be accomplished when using the 3M Locator Plates, Series 3443-82-XX and the
3M
™
Assembly Press, Models 3640 or 3335.
3436-1K Shut Height Setting
Press
3640/3316
7
7
7
7
7
7
7
7
7
Press 3335
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
Connector
Part Number
45104
45106
45108
45110
45112
45114
45116
45120
45130
Locator
Plate Number
3443-82-04
3443-82-06
3443-82-08
3443-82-10
3443-82-12
3443-82-14
3443-82-16
3443-82-20
3443-82-30
Platen
Part Number
3442-9
3442-9
3442-9
3442-9
3442-9
3442-9
3442-9
3442-9
3442-9
November 2013
78-9101-8937-8
3
2.0
2.1
Procedures for Set-up
Adjust the shut height settings. (See Figures 2-4)
Cable Stop Holes
Cable Location Area
Assembly
Press Base
Mounting Holes
(4 Places)
Figure 1: 3M
™
Locator Plate 3443-82-20
3.0
Procedures for Adjusting Shut Height
3.3
The shut height should be adjusted from the base
before the locator plate is put into place.
The 3M
™
Assembly Presses 3316 and 3640 are
adjusted with a knob at the top of the press. The
3M
™
Assembly Press 3335 is adjusted with the collar
on the press shaft, and the 3M
™
Assembly Press 3830
are self-adjusting.
3.1
3.2
Place the shut height gauge across the
press base.
The shut height adjustment is made from the
base of the assembly press without the locator
plate or platen in place.
Lower the handle of the press until the handle
casting makes contact with the
press casting. (See Figure 2)
Figure 3
3.4
Rotate the shut height to lower or raise
adjustment feature until the bottom of the
shaft contacts the desired position on the shut
height gauge. (See Figures 3 and 4)
Figure 2
Figure 4
2
3.5
Install the 3M
™
Locator Plate and the
appropriate platen on the press. The platen
should be positioned parallel with the
connector body and cover.
(see Figure 5)
5.0
5.1
Procedures for Cable Termination
Place the socket connector onto the cover over
the cable, verifying the pin 1 indicator
is in the correct position. (see Figure 8)
After the cable is prepared it is ready for termination.
Figure 5
Figure 8
4.0
4.1
Procedures for Cable Preparation
Place the cover into the locator plate.
(See Figure 6)
Before assembly of the connector can take place, the
cable must be prepared.
5.2
Bring the handle of the press down until the
IDCs press into cable and the connector fully
seats into the cover. (see Figure 9)
Figure 9
5.3
Figure 6
Visually inspect termination to ensure
that:
4.2
Place the properly sized ribbon cable onto the
cover in the locator plate. (See Figure 7)
a. Cover is fully seated and parallel to
the body.
b. Cable is properly aligned with the cover.
c. Cover retaining devices on the body
are flush with the cover end.
(See Figure 10)
Figure 7
a. 0.0625 dowel pins can be used in the
cable stop location holes if so desired.
(Cable stop location holes not available
on sizes 4, 6, 8 and 10.)
Figure 10
3
6.0
6.1
Strain Relief Attachment
Fold the cable back over the cover.
(See Figure 11)
6.3
Press the strain relief down until the strain
relief snaps into the correct position on the
connector. (See Figure 13)
Figure 11
Figure 13
6.2
Place the strain relief in the connector over the
cable, sliding the strain relief into the slots of
the connector. (See Figure 12)
Figure 12
Customer and Technical Service
Within the U.S.:
Customer Service: 800-225-5373
3M is a trademark of 3M Company.
Outside of the U.S.:
For customer service, please contact your local 3M Electronic
Solutions Division representative.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current
publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by
an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.
3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product
or refund the purchase price of the 3M product.
Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or
consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Now, most of the information I can find is in English. I am not good at English. Can anyone give me some advice? Where are there many websites that specialize in downloading Chinese information about ...
I personally think that development boards (learning boards) are provided to users for learning and secondary development. Since they are provided to users for secondary development, I think they shou...
As portable medical devices have become a new growth trend, equipment manufacturers are looking for technologies and products that can reduce development difficulty and shorten time to market. TI's MS...
Download the full set of ultra-stable Protel99se plus automatic Chinese package http://www.vip998.com/Soft/ShowSoftDown.asp?UrlID=1SoftID=50Download the full set of the ultra-stable Protel99se plus au...
1. No one forced you, you chose Symbian OS voluntarily. 2. This is the most important question, is there a future for developing software for Symbian OS? Every Symbian OS developer is considering this...
I read one of your posts about 34063, which said that the efficiency can reach 97%. I admire it very much. Now I have also drawn a diagram of 34063. Please give me some guidance. If the input is 5V/2A...
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
The structure of an LCD TV primarily consists of the LCD display module, power module, driver module (primarily including the main driver board and tuner board), and keypad module. LCD display modu...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
On August 25th, TSMC, the world's leading contract chip manufacturer, attracted significant attention for its decision to build a chip manufacturing facility in Arizona. TSMC primarily manufactures...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
Smartphones have become essential digital devices, and the growing number of smartphone-centric applications is enriching people's lives. As users, they desire a better app experience and a wider r...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
Puttshack's Trackaball uses the Nordic nRF54L15 system-on-chip (SoC) to monitor sensors and enable Bluetooth low energy connectivity, while the nPM2100 power management integrated circuit (PMIC) ...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
