1.5KE18T-G datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Discrete semiconductor> diode> 1.5KE18T-G

1.5KE18T-G: DescriptionTrans Voltage Suppressor Diode, 14.5V V(RWM), Unidirectional,; CategoryDiscrete semiconductor diode; File Size66KB，6 Pages; ManufacturerComchip Technology; Websitehttp://www.comchiptech.com/; Environmental Compliance

Download Datasheet Parametric View All

1.5KE18T-G Overview

Trans Voltage Suppressor Diode, 14.5V V(RWM), Unidirectional,

1.5KE18T-G Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	_compli
ECCN code	EAR99
Breakdown voltage nominal value	18 V
Maximum clamping voltage	26.5 V
Diode type	TRANS VOLTAGE SUPPRESSOR DIODE
JESD-609 code	e3
polarity	UNIDIRECTIONAL
Maximum repetitive peak reverse voltage	14.5 V
surface mount	NO
Terminal surface	Tin (Sn)
Base Number Matches	1

Preview

Download Datasheet

View All

1500W Transient Voltage Suppressor

COMCHIP

SMD Diodes Specialist

1.5KE-G Series

Stand-off Voltage: 6.8 ~ 600V

Power Dissipation: 1500 Watts

RoHS Device

Features

-Glass passivated chip.

-Low leakage.

-1500W peak pulse power capability with a 10/1000μs

waveform, repetitive rate (duty cycle): 0.01%.

-Uni and Bidirectional unit.

-Excellent clamping capability.

-Very fast response time.

0.375(9.53)

0.285(7.24)

1.000(25.40) Min.

DO-201

Mechanical Data

-Case: Molded plastic DO-201

-Epoxy: UL 94V-0 rate flame retardant

-Terminals: Axial leads, solderable per

MIL-STD-202, Method 208 guranteed

-Polarity: Color band denotes cathode

end except Bipolar

-Mounting position: Any

-Approx. weight: 0.844 grams

0.209(5.30) DIA.

0.189(4.79) DIA.

1.000(25.40) Min.

0.042(1.07)

DIA.

0.038(0.97)

DIA.

Dimensions in inches and (millimeter)

Maximum Ratings and Electrical Characteristics

=25°C unless otherwise noted)

Parameter

Peak power dissipation with a 10/1000

waveform (Note 1)

Peak pulse current with a 10/1000

μs

waveform

(Note 1)

Power dissipation on infinite heatsink at T

=75°C

Peak forward surge current, 8.3ms single

half sine-wave unidirectional only

(JEDEC method) (Note 2)

Maximum instantaneous forward voltage at

100 A for unidirectional only(Note 3)

Operating junction and storage

temperature range

Symbol

Value

1500

Unit

See Next Table

6.5

FSM

200

3.5/5.0

, T

STG

-55 to +150

°C

NTOES:

(1) Non-repetitive current pulse, per fig.5 and derated above T

=25°C per fig.1

(2) Measured on 8.3ms single half sine-wave or equivalent square wave, equare wave, duty cycle=4 pulses per minute maximum

(3) V

<3.5V for devices of V

<200V and V

<5.0V for devices of V

>201V

REV:B

QW-BTV07

Page 1

Recommended Resources

Application of integrated circuit TDA2822

intermittent irrigation controller circuit

Public telephone charge sound and light reminder circuit circuit diagram

Capacitive divider clamped single-ended flyback switching regulated power supply

Protection switch

875p computer motherboard circuit diagram_037

[TI recommended course] #Boost and buck-boost DCDC converters help wireless charging design#: //training.eeworld.com.cn/TI/show/course/5501...; wo4fisher TI Technology Forum

Msp430f1232 data and AQ430: In response to the request of DIY light stick, I started to get in touch with MSP430. So I searched for some relevant information, hoping to help novices like me: [[i] This post was last edited by chi...; chich Microcontroller MCU

PCINT level change interrupt: What is the interrupt vector number for the PCINT14 level change interrupt? The manual only lists the interrupt vector numbers for PCINT0 and PCINT1....; waltonandwalton Microchip MCU

Is the forum infected?: Searching for "AVR" through 360 browser will bring up this interface . If you click on "Electronic Engineering World Forum", it will become this and . But if you close these two pages and then enter a...; yqiqi Suggestions & Announcements

Recruitment: One RF engineer, Location: Shenzhen: Job requirements: 1. Bachelor degree or above, graduated from radio, communication engineering and other related majors; 2. 3 years or more of design, development or maintenance experience in high-fre...; lizengmao Embedded System

I want to increase the common-mode input voltage. Will this be a problem?: The power supply of the amplifier is +-5V. I want to measure the voltage between 10V and 12.5V. I tried this circuit and the voltage at the input of the amplifier (pin 8 and pin 1) is already greater ...; littleshrimp Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components