EEWORLDEEWORLDEEWORLD

Part Number

Search

E1UMA10-20.480MTR

Description
QUARTZ CRYSTAL RESONATOR, 20.48MHz, ROHS COMPLIANT, RESISTANCE WELDED PACKAGE-2
CategoryPassive components    Crystal/resonator   
File Size98KB,4 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance
Download Datasheet Parametric View All

E1UMA10-20.480MTR Overview

QUARTZ CRYSTAL RESONATOR, 20.48MHz, ROHS COMPLIANT, RESISTANCE WELDED PACKAGE-2

E1UMA10-20.480MTR Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionROHS COMPLIANT, RESISTANCE WELDED PACKAGE-2
Reach Compliance Codecompli
Other featuresAT-CUT CRYSTAL; TAPE AND REEL
Ageing5 PPM/YEAR
Crystal/Resonator TypePARALLEL - FUNDAMENTAL
Drive level1000 µW
frequency stability0.002%
frequency tolerance15 ppm
JESD-609 codee3
load capacitance10 pF
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency20.48 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
physical sizeL11.18XB4.7XH2.5 (mm)/L0.44XB0.185XH0.098 (inch)
Series resistance50 Ω
surface mountNO
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrie
Base Number Matches1
E1UMA10-20.480M TR
Series
RoHS Compliant (Pb-free) Resistance Welded Short
HC-49/US Crystal
Frequency Tolerance/Stability
±15ppm at 25°C, ±20ppm over -40°C to +85°C
Mode of Operation
AT-Cut Fundamental
RoHS
Pb
Packaging Options
Tape & Reel
E1U M A 10 -20.480M TR
Nominal Frequency
20.480MHz
Load Capacitance
10pF Parallel Resonant
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
Aging at 25°C
Load Capacitance
Shunt Capacitance (C0)
Equivalent Series Resistance
Mode of Operation
Drive Level
Storage Temperature Range
Insulation Resistance
20.480MHz
±15ppm at 25°C, ±20ppm over -40°C to +85°C
±5ppm/year Maximum
10pF Parallel Resonant
7pF Maximum
50 Ohms Maximum
AT-Cut Fundamental
1mWatt Maximum
-40°C to +125°C
500 Megaohms Minimum at 100Vdc
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
Gross Leak Test
Lead Integrity
Lead Termination
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 1014 Condition A
MIL-STD-883, Method 1014 Condition C
MIL-STD-883, Method 2004
Sn 2µm - 6µm
MIL-STD-202, Method 213 Condition C
MIL-STD-202, Method 210
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007 Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
LINE MARKING
1
E20.480M
E=Ecliptek Designator
M=MHz
6.35
MIN
DIA 0.457
±0.051(X2)
11.18
MAX
4.88 ±0.20
2.50 MAX
4.70
MAX
www.ecliptek.com | Specification Subject to Change Without Notice | Rev E 8/12/2010 | Page 1 of 4

Recommended Resources

【Recruitment】Senior ATE Test Development Engineer
[i=s]This post was last edited by lgdjade on 2014-10-9 23:45[/i] I am from Rosenberger Technology, we are a German-owned company, dedicated to the research and development and manufacturing of telecom...
lgdjade Recruitment
Problems with compiling driver programs under Linux
When compiling the driver for the clock chip, the following errors occur: undefined reference to `gpio_line_config' undefined reference to `gpio_line_config' undefined reference to `gpio_line_set' und...
rong8481 Linux and Android
How to distinguish 1/4"CCD and 1/3"CCD?
To summarize a few points, I hope friends can add to it: 1. Look at the pins: 14 pins are 1/4, 16 pins are 1/3; 2. Visual inspection: one-third is much larger than one-quarter CCD; 3. Effect: using th...
小瑞 Industrial Control Electronics
ADI Blackfim high-end solution BF561 Chinese technical data
You can take a look to see if it can help you with the ongoing blackfin DSP development....
flyingdsp DSP and ARM Processors
About the MAX706 reset problem
I am working on a handheld project recently. I need to use the zigbee module on the handheld. When I turn on the zigbee module, the handheld will reset and shut down. I tested that when the zigbee mod...
lxianchao stm32/stm8
Question about STM32F4 Cube library UART DMA, what is __HAL_Lock()?
In the F4 CUBE library provided by STM32, the following code is provided in stm32f4XX_hal_def.h: [code]#if (USE_RTOS == 1) /* Reserved for future use */ #error “USE_RTOS should be 0 in the current HAL...
liutogo stm32/stm8

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 107  2103  916  2354  66  3  43  19  48  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号