RADIALL
TECHNICAL DATA SHEET
R 514 - - - - - -
Issue : 18-Nov-2010
TERMI
I
NATED MULTI
I
PORT SWI
I
TCHES:
:
TI
I
TANI
I
UM Seri
i
es
TERM NATED MULT PORT SW TCHES T TAN UM Ser es
SPnT Coaxial Switches DC to 6 GHz, DC to 20 GHz, DC to 26.5 GHz, DC to 40 GHz
Radiall’s TITANIUM switches are optimised to perform at a high level over an extended life span. With
outstanding RF performances, and a guaranteed Insertion Loss repeatability of 0.03 dB over a life span of 2,5
million switching cycles. RADIALL TITANIUM switches are perfect for automated test and measurement
equipment, as well as signal monitoring devices.
PART NUMBER SELECTION
R 514 . 73 . . 7 .
RF Connectors :
3 : SMA up to 6 GHz
4 : SMA up to 20 GHz
F : SMA up to 26.5 GHz
8 : SMA 2.9 up to 40 GHz
Documentation :
-
: Certificate Of Conformity
C : Calibration certificate
R : Calibration certificate +
RF curves
Type :
7 : Latching + Self cut-off + Auto Reset + Indicators
Actuator Terminal :
7 : HE 10 receptacle, delivered
with 750 mm (30 inches)
ribbon cable + HE10
connector
Number of Positions :
4 : 4 positions
6 : 6 positions
Options :
1 : Positive common (without TTL)
2 : TTL/5V logic with 24 Vdc supply
PICTURE
ISO 9001 certified
www.radiall.com
Page
1
E-Mail : switchingproducts@radiall.com
RADIALL
RF PERFORMANCES
TECHNICAL DATA SHEET
R 514 - - - - - -
Issue : 18-Nov-2010
TERMI
I
NATED MULTI
I
PORT SWI
I
TCHES:
:
TI
I
TANI
I
UM Seri
i
es
TERM NATED MULT PORT SW TCHES T TAN UM Ser es
PART NUMBER
R5143734-7
R5143736-7
GHz
DC to 6
R5144734-7
R5144736-7
DC to 20
R514F734-7
R514F736-7
DC to 26.5
R5148734-7
R5148736-7
DC to 40
Frequency Range
Impedance
Ohms
50
Insertion Loss dB
(Maximum)
0.3 + 0.015 x frequency (GHz)
Isolation dB
(Minimum)
80
DC to 6 GHz
:
6 to 12.4 GHz :
12.4 to 20 GHz :
80
70
65
DC to 6 GHz
6 to 12.4 GHz
12.4 to 20 GHz
20 to 26.5 GHz
:
:
:
:
80
70
65
60
DC to 6 GHz
6 to 12.4 GHz
12.4 to 20 GHz
20 to 26.5 GHz
26.5 to 40 GHz
:
:
:
:
:
80
70
65
60
55
V.S.W.R.
(Maximum)
1.20
DC to 6 GHz
6 to 12.4 GHz
12.4 to 18 GHz
18 to 20 GHz
:
:
:
:
1.20
1.35
1.45
1.70
DC to 6 GHz :
6 to 12.4 GHz :
12.4 to 18 GHz :
18 to 26.5 GHz :
1.20
1.35
1.45
1.70
DC to 6 GHz :
6 to 12.4 GHz :
12.4 to 18 GHz :
18 to 26.5 GHz :
26.5 to 40 GHz :
1.20
1.35
1.45
1.70
1.90
Third order Inter
Modulation
Repeatability
(measured at 25°
C)
-120 dBc typical (2 carriers 20W)
0.03 dB
0.05 dB
TYPICAL RF PERFORMANCES
Insertion Loss and Isolation
V.S.W.R.
ISO 9001 certified
www.radiall.com
Page
2
E-Mail : switchingproducts@radiall.com
RADIALL
TECHNICAL DATA SHEET
R 514 - - - - - -
Issue : 18-Nov-2010
TERMI
I
NATED MULTI
I
PORT SWI
I
TCHES:
:
TI
I
TANI
I
UM Seri
i
es
TERM NATED MULT PORT SW TCHES T TAN UM Ser es
ADDITIONAL SPECIFICATIONS
Operating mode
Nominal operating voltage
(across operating temperature) Vdc
Coil resistance
(+/-10%)
Nominal operating current at 23°
C
Maximum stand-by current
Ohms
mA
mA
RF path
Average power
Internal terminations
High Level
TTL input
Low Level
0 to 0.8 V
Maximum withstanding voltage :
Maximum current capacity
:
Maximum « ON » resistance
:
Minimum « OFF » resistance
:
ms
SMA
Life
(min)
for
SMA 2.9
Connectors
Actuator terminal
Weight
(max)
g
1 million cycles
SMA – SMA 2.9
15
2,5 million cycles
3 to 7 V
Latching
24
(20 / 32)
120
200
50
Cold switching : see Power Rating Chart on page 8
Hot switching : 1 Watt CW
1 Watt average into 50
Ω
1.4 mA max at Vcc = Max
Indicator specifications
60V
150 mA
2.5
Ω
100 MΩ
Switching time
(max)
HE10 ribbon receptacle
230
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
Storage temperature range
Temperature cycling
(MIL-STD-202 , Method 107D , Cond.A)
Vibration
(MIL STD 202 , Method 204D , Cond.D)
Shock
(MIL STD 202 , Method 213B , Cond.C)
Moisture resistance
(MIL STD 202 , Method 106E , Cond.E)
Altitude storage
(MIL STD 202 , Method 105C , Cond.B)
RFI
(MIL STD 1344 , Method 3008 or IEC 61726)
Magnetic field
°
C
°
C
°
C
-25 to +75
-55 to +85
-55 to +85 (10 cycles)
10-2000 Hz , 10g
50g / 6 ms , ½ sine
operating
operating
65° 95% RH, 10 days
C,
50,000 feet (15,240 meters)
55dB at 20GHz
< 5.10
-5
gauss at 1 meter
ISO 9001 certified
www.radiall.com
Page
3
E-Mail : switchingproducts@radiall.com
RADIALL
TECHNICAL DATA SHEET
R 514 - - - - - -
Issue : 18-Nov-2010
TERMI
I
NATED MULTI
I
PORT SWI
I
TCHES:
:
TI
I
TANI
I
UM Seri
i
es
TERM NATED MULT PORT SW TCHES T TAN UM Ser es
ELECTRONIC POSITION INDICATORS
The electronic position indicators utilise photo-MOS transistors which are driven by the mechanical position of
the RF paths moving elements. The circuitry consists of a common which can be connected to an output
corresponding to selected RF path. If one or several RF paths are closed, the corresponding indicators are
connected to the common. The photo-MOS transistors are configured for AC and/or DC operation. The electronic
position indicators require the supply (20 to 32 VDC) to be connected to pin 1 and ground connected to pin 15.
Ways 1 and 4 are not connected for SP4T switches.
ISO 9001 certified
www.radiall.com
Page
4
E-Mail : switchingproducts@radiall.com
RADIALL
TECHNICAL DATA SHEET
R 514 - - - - - -
Issue : 18-Nov-2010
TERMI
I
NATED MULTI
I
PORT SWI
I
TCHES:
:
TI
I
TANI
I
UM Seri
i
es
TERM NATED MULT PORT SW TCHES T TAN UM Ser es
DRIVING THE SWITCH
: Type 7 : with TTL (option “2”) / without TTL (option “1”).
Each RF path can be closed by applying Ground or TTL "High" for option 2 to the corresponding "drive" pin. In
general, except for Make-Before-Break drive, all other RF paths are simultaneously opened by internal logic.
Standard drive option “1”
•
Connect pin 15 to ground.
•
Connect pin 1 to supply (+20 VDC to +32
VDC)
•
Select (close) desired RF path by applying
Ground to the corresponding "drive" pin (Ex:
apply Ground to pin 3 to close RF path 1).
•
To select another path, ensure that all
unwanted RF path "drive" pins are
disconnected from Ground (to prevent
multiple RF path engagement). Apply
Ground to the "drive" pin which corresponds
to the desired RF path.
•
To open all RF paths, ensure that all RF
path "drive" pins are disconnected from
Ground. Complete the operation by applying
Ground to pin 16.
TTL drive option “2”
•
Connect pin 15 to ground.
•
Connect pin 1 to supply (+20 VDC to +32
VDC)
•
Select (close) desired RF path by applying
TTL "High " to the corresponding "drive" pin
(Ex: apply TTL "High" to pin 3 to close RF
path 1).
•
To select another path, ensure that all
unwanted RF path "drive" pins are in TTL
"Low" position (to prevent multiple RF path
engagement). Apply TTL "High" to the
"drive" pin which corresponds to the desired
RF path.
•
To open all RF paths, ensure that all RF
path "drive" pins are in TTL "Low" position.
Complete the operation by applying TTL
"High" to pin 16.
Break-Before-Make
Open the undesired RF path. After 15 ms
(minimum), close the new RF port.
Make-Before-Break
Ensure that the previously selected RF path
“drive” is connected to Ground (or TTL
“High” for option “2”, then close the new RF
path.
Ways 1 and 4 are not connected for SP4T switches.
ISO 9001 certified
www.radiall.com
Page
5
E-Mail : switchingproducts@radiall.com
京公网安备 11010802033920号
EEWORLD
