K4S281632D
CMOS SDRAM
128Mbit SDRAM
2M x 16Bit x 4 Banks
Synchronous DRAM
LVTTL
Rev. 0.1
Sept. 2001
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 0.1 Sept. 2001
K4S281632D
Revision History
Revision 0.0 (Mar. 06, 2001)
Revision 0.1 (Sep. 06, 2001)
•
•
CMOS SDRAM
Redefined IDD1 & IDD4 in DC Characteristics
Changed the Notes in Operating AC Parameter.
< Before >
5. For 1H/1L, tRDL=1CLK and tDAL=1CLK+tRP is also supported .
SAMSUNG recommends tRDL=2CLK and tDAL=2CLK + tRP.
< After >
5.In 100MHz and below 100MHz operating conditions, tRDL=1CLK and tDAL=1CLK + 20ns is also supported.
SAMSUNG recommends tRDL=2CLK and tDAL=2CLK + tRP.
Rev. 0.1 Sept. 2001
K4S281632D
2M x 16Bit x 4 Banks Synchronous DRAM
FEATURES
• JEDEC standard 3.3V power supply
• LVTTL compatible with multiplexed address
• Four banks operation
• MRS cycle with address key programs
-. CAS latency (2 & 3)
-. Burst length (1, 2, 4, 8 & Full page)
-. Burst type (Sequential & Interleave)
• All inputs are sampled at the positive going edge of the system
clock.
• Burst read single-bit write operation
• DQM for masking
• Auto & self refresh
• 64ms refresh period (4K cycle)
Part No.
K4S281632D-TC/L55
K4S281632D-TC/L60
K4S281632D-TC/L7C
K4S281632D-TC/L75
K4S281632D-TC/L1H
K4S281632D-TC/L1L
CMOS SDRAM
GENERAL DESCRIPTION
The K4S281632D is 134,217,728 bits synchronous high data
rate Dynamic RAM organized as 4 x 2,097,152 words by 16
bits, fabricated with SAMSUNG′s high performance CMOS
technology. Synchronous design allows precise cycle control
with the use of system clock I/O transactions are possible on
every clock cycle. Range of operating frequencies, programma-
ble burst length and programmable latencies allow the same
device to be useful for a variety of high bandwidth, high perfor-
mance memory system applications.
ORDERING INFORMATION
Max Freq.
183MHz(CL=3)
166MHz(CL=3)
133MHz(CL=2)
133MHz(CL=3)
100MHz(CL=2)
100MHz(CL=3)
LVTTL
54
TSOP(II)
Interface Package
FUNCTIONAL BLOCK DIAGRAM
I/O Control
LWE
Data Input Register
LDQM
Bank Select
2M x 16
2M x 16
2M x 16
2M x 16
Refresh Counter
Output Buffer
Row Decoder
Sense AMP
Row Buffer
DQi
Address Register
CLK
ADD
Column Decoder
Col. Buffer
Latency & Burst Length
LRAS
LCBR
LCKE
LRAS
LCBR
LWE
LCAS
Programming Register
LWCBR
LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
LDQM
UDQM
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 0.1 Sept. 2001
K4S281632D
PIN CONFIGURATION
(Top view)
V
DD
DQ0
V
DDQ
DQ1
DQ2
V
SSQ
DQ3
DQ4
V
DDQ
DQ5
DQ6
V
SSQ
DQ7
V
DD
LDQM
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
V
DD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
V
SS
DQ15
V
SSQ
DQ14
DQ13
V
DDQ
DQ12
DQ11
V
SSQ
DQ10
DQ9
V
DDQ
DQ8
V
SS
N.C/RFU
UDQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
V
SS
CMOS SDRAM
54Pin TSOP (II)
(400mil x 875mil)
(0.8 mm Pin pitch)
PIN FUNCTION DESCRIPTION
Pin
CLK
CS
Name
System clock
Chip select
Input Function
Active on the positive going edge to sample all inputs.
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
Row/column addresses are multiplexed on the same pins.
Row address : RA
0
~ RA
11
, Column address : CA
0
~ CA
8
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
Makes data output Hi-Z, t
SHZ
after the clock and masks the output.
Blocks data input when L(U)DQM active.
Data inputs/outputs are multiplexed on the same pins.
Power and ground for the input buffers and the core logic.
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
This pin is recommended to be left No Connection on the device.
CKE
Clock enable
A
0
~ A
11
BA
0
~ BA
1
RAS
CAS
WE
L(U)DQM
DQ
0
~
15
Address
Bank select address
Row address strobe
Column address strobe
Write enable
Data input/output mask
Data input/output
Power supply/ground
Data output power/ground
No connection
/reserved for future use
V
DD
/V
SS
V
DDQ
/V
SSQ
N.C/RFU
Rev. 0.1 Sept. 2001
K4S281632D
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on any pin relative to Vss
Voltage on V
DD
supply relative to Vss
Storage temperature
Power dissipation
Short circuit current
Symbol
V
IN
, V
OUT
V
DD
, V
DDQ
T
STG
P
D
I
OS
Value
-1.0 ~ 4.6
-1.0 ~ 4.6
-55 ~ +150
1
50
CMOS SDRAM
Unit
V
V
°C
W
mA
Note :
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to V
SS
= 0V, T
A
= 0 to 70°C)
Parameter
Supply voltage
Input logic high voltage
Input logic low voltage
Output logic high voltage
Output logic low voltage
Input leakage current
Symbol
V
DD
, V
DDQ
V
IH
V
IL
V
OH
V
OL
I
LI
Min
3.0
2.0
-0.3
2.4
-
-10
Typ
3.3
3.0
0
-
-
-
Max
3.6
V
DD
+0.3
0.8
-
0.4
10
Unit
V
V
V
V
V
uA
Note
4
1
2
I
OH
= -2mA
I
OL
= 2mA
3
Notes :
1. V
IH
(max) = 5.6V AC.The overshoot voltage duration is
≤
3ns.
2. V
IL
(min) = -2.0V AC. The undershoot voltage duration is
≤
3ns.
3. Any input 0V
≤
V
IN
≤
V
DDQ
,
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
4. The VDD condition of K4S281632D-60 is 3.135V~3.6V.
CAPACITANCE
Clock
(V
DD
= 3.3V, T
A
= 23°C, f = 1MHz, V
REF
=1.4V
±
200 mV)
Pin
Symbol
C
CLK
C
IN
C
ADD
C
OUT
Min
2.5
2.5
2.5
4.0
Max
4.0
5.0
5.0
6.5
Unit
pF
pF
pF
pF
Note
1
2
2
3
RAS, CAS, WE, CS, CKE, DQM
Address
DQ
0
~ DQ
15
Notes :
1. -75/7C specify a maximum value of 3.5pF
2. -75/7C specify a maximum value of 3.8pF
3. -75/7C specify a maximum value of 6.0pF
Rev. 0.1 Sept. 2001
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
