13000 series
Professional quick-break momentary pushbutton switches
Distinctive features and specifications
❑
PC and panel mount models
❑
Bushing Ø 6,35 (1/4) and 11,9 (15/32)
❑
UL and CECC approved
B
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load :
- silver contacts (A-AD2) : 2A 250VAC - 4A 125VAC - 4A 30VDC
- gold plated contacts (CD) : 100mA 30V
• Minimum load (AD2-CD contacts) : 10mA 50mV, 10µA 5V min.
• Initial contact resistance : 10 mΩ max.
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
2.000 Vrms 50 Hz min. between poles and between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life :
Contacts
A
AD2
CD
Max. current/voltage rating
2A 250VAC - 4A 125VAC - 4A 30VDC
2A 250VAC - 4A 125 VAC - 4A 30VDC
(gold plating : 100mA 30VDC max.)
100mA 30VDC
Low level or mechanical life
Number of cycles
50.000
20.000
50.000
150.000
MATERIALS
GENERAL SPECIFICATIONS
• Case : diallylphthalate (DAP)
• Actuator : brass, chrome plated
• Bushing : brass, nickel plated
• Housing : brass, nickel plated
• Contacts :
A
: silver
AD2
: silver, gold plated
(2 micron gold)
CD
: brass, gold plated
• Terminal seal : epoxy
Note : AD2 contacts can be used for high level applications.In this case, the
gold layer is considered only as a protection against oxidation during
storage.
• Torque : 1,25 Nm (.922 Ft.lb)
max. applied to nut
• Standard panel thickness : 2 mm
(.078 ) max.
• Total travel : 2 mm (.078)
• Operating temperature :
-40°C to +85°C
B-62
www.apem.com
APEM
13000 series
Professional quick-break momentary pushbutton switches
Specifications
RELIABILITY
-
RUN
-
IN TEST
Upon request, each individual switch can be submitted to a low level run-in
test of 50 or 250 cycles to ensure suitability for special applications requiring
a very high level of reliability (military, space,etc.).
AGENCY APPROVALS
/
PREFERENTIAL LISTS
CECC 96401-001
QPL
(Europe only)
MUAHAG
Designed to
MIL
specifications
Availability
:
UL : all models with silver or gold plated silver contacts
CECC : consult factory for details of approved models.
Marking
: to order switches marked UL or CECC, complete appropriate box
of ordering format.
Preferential lists do not appear on the switches.
B
Dimensions
: first dimensions are in mm while inches are shown as bracketted numbers.
Sealing boots
are available to protect the switches against dust and water. They are presented in section H.
Mounting accessories
: standard hardware supplied with all models : 2 hex nuts 8 mm (.314) across flats, 1 locking ring and
1 lockwasher.
Standard and special hardware available are presented in section I.
Packaging unit
: 50 pieces.
APEM
www.apem.com
B-63
13000 series
Professional quick-break momentary pushbutton switches
Overview
13
SERIES
Terminals and bushing
2
4
Straight PC terminals,
bushing Ø 6,35 (1/4)
Solder lugs, bushing Ø 6,35
(1/4) or 11,9 (15/32)
Right angle terminals,
bushing Ø 6,35 (1/4)
3
4
No of poles
Single pole
Double pole
5
Electrical function
ON
-
MOM
Terminals
Blank
Solder lugs or straight PC
depending on model
W
Right angle, horizontal
mounting
B
Contact materials
A
AD2
CD
Silver
Silver, gold plated
(2 micron gold)
Brass, gold plated
Finish
Blank
Bright chrome finish
G
Matt black finish on
bushing, plunger and
hardware
Blank
X640
X768
Special options
No special
requirement
Reinforced sealing
by three O-rings
Bushing Ø 11,9
(15/32) + front
panel sealing
(double pole only)
U900
U1140
U1720
U480
U630
U2430
U2020
Caps
Ø 5 (.196)
Ø 8 (.314)
Ø 9,4 (.370)
Ø 10 (.393) std
Ø 15 (.590)
Square, height
4 (.157)
Square, height
6 (.236)
For models with Ø 4
(.157) plunger only.
Plungers
Blank
Standard for Ø 6,35
(1/4) bushing
4
4 mm (.157) long, for
Ø 11,9 (15/32)
bushing (X768)
9 mm (.354) long, for
Ø 11,9 (15/32)
bushing (X768)
Sealing
Blank
Epoxy sealed
terminals standard
K
Front panel sealing by
one O-ring and
sealing washer
Reinforced sealing, see X640
under "Special options".
Approvals
UL
CECC
Availability :
Consult factory for
details of approved
models.
9
: please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
NOTICE
ABOUT THIS SERIES
On the following pages, you will find successively :
- model structure of switches
- options in the same order as in above chart
B-64
www.apem.com
APEM
13000 series
Professional quick-break momentary pushbutton switches
Solder lug terminals : 13400 - Straight PC terminals : 13200
➞
Keyway
•
Threaded bushing
Ø 6,35 mm (1/4)
• Epoxy sealed terminals standard
1.70
(.066)
5.00
(.196)
9.50
(.374)
1 2 3
1.20
(.047)
1.00
(.039)
2.50
(.098)
MODEL
STRUCTURE
B
➞
Keyway
Ø6.35-40UNS
(1/4-40UNS)
Ø4.00
(.157 DIA)
6.00
(.236)
8.00
(.314)
14.00
(.551)
Solder lug terminals : 13400
1-3
Single pole
13435
Double pole
13445
ON
1-2
MOM
6.30
(.248)
ON
MOM
EPOXY
2.50
(.098)
4.00
(.157)
5.00
(.196)
0.50
(.019)
6.00
(.236)
Straight PC terminals : 13200
➞
Keyway
Ø6.35-40UNS
(1/4-40UNS)
6.00
(.236)
4.00
(.157)
Ø1.6
(.062 DIA)
6.30
(.248)
13.40
(.527)
0.70
(.027)
6.00
(.236)
8.00
(.314)
Ø4.00
(.157 DIA)
14.00
(.551)
1-3
Single pole
13235
Double pole
13245
ON
1-2
MOM
EPOXY
1
2
3
ON
MOM
1.00
(.039)
4.00
(.157)
9.50
(.374)
0.50
(.019)
6.00
(.236)
4.00
(.157)
PANEL CUT
-
OUT
13400 - 13200
Ø6.50
(.255 DIA)
Ø2.20
(.086 DIA)
Ø6.50
(.255 DIA)
Ø6.50
(.255 DIA)
5.20
(.204)
1.10
(.043)
2.70
(.106)
2.70
(.106)
Standard
With
K
sealing option
With
X640
sealing option
APEM
www.apem.com
0.70
(.027)
13.40
(.527)
1
2
3
B-65
13000 series
Professional quick-break momentary pushbutton switches
Right angle terminals : 13400W
Right angle terminals - single pole
➞
Keyway
Ø6.35-40UNS
(1/4-40UNS)
6.00
(.236)
8.00
(.314)
Ø4.00
(.157 DIA)
Ø1.6
(.062 DIA)
5.08
(.200)
0.40
(.015)
5.90
(.232)
9.27
(.364)
2.60
(.102)
0.70
(.027)
1
2
3
13.40
(.527)
4.00
(.157)
1.00
(.039)
4.40
(.173) EPOXY
4.00
(.157)
0.50
(.019)
14.20
(.559)
4.00
(.157)
B
Panel cut-out, see previous page.
CONTACT MATERIALS
A
AD2
CD
Silver
Silver, gold plated (2 micron gold)
Brass, gold plated
PLUNGER
Dash compulsory before plunger code.
Blank
-4
-9
Standard plunger for Ø 6,35 (1/4) bushing
4 mm (.157) long plunger for Ø 11,9 (15/32) bushing (X768 option)
9 mm (.354) long plunger for Ø 11,9 (15/32) bushing (X768 option)
B-66
www.apem.com
APEM
9.27
(.364)
13435W
1-3
ON
1-2
MOM
stm32/stm8
京公网安备 11010802033920号
EEWORLD
