EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8ALF-01-23R2-F-

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 23.2ohm, 1% +/-Tol, -100,100ppm/Cel, 4422,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GM8ALF-01-23R2-F- Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 23.2ohm, 1% +/-Tol, -100,100ppm/Cel, 4422,

GUB-GM8ALF-01-23R2-F- Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid796074031
package instructionSMT, 4422
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.25
structureMolded
JESD-609 codee3
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package formSMT
Package width5.588 mm
Rated power dissipation(P)0.16 W
resistance23.2 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4422
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
x Newcomer help
I am a novice and I have recently been learning according to the soc training materials, but I cannot install the 13th version of quartus in the textbook, so I installed the 15th version. When I used ...
lu112233 FPGA/CPLD
Comparison of several typical connection methods of optocoupler isolation in switching power supply
In general isolated power supplies, optocoupler isolated feedback is a simple and low-cost method. However, there has been no in-depth research on the various connection methods and differences of opt...
qwqwqw2088 Analogue and Mixed Signal
DSP Programming--5.31--Hardware Interrupt Management
[size=4]In order to correctly respond to hardware interrupts and for the stability of the DSP/BIOS kernel, please pay special attention to the following points when writing HWI hardware ISRs: [/size] ...
Jacktang DSP and ARM Processors
[Xianji HPM6750 Review] Testing CAN Transceiver
HPM6750 has 4 CAN controllers and supports CANFD. Currently, CAN2.0 is more commonly used in industry, so this evaluation uses CAN1 controller. The CAN driver chip uses TI's VD230, and the computer us...
xiashuang Domestic Chip Exchange
MSP430F5529 clock and FLL configuration
1. Basic1.5529 contains five clock sourcesXT1CLK: external low-frequency crystal oscillator, 32.786KHz, can be used as FLL reference power supply, can also be adjusted from 4MHZ to 32MhzXT2CLK: extern...
灞波儿奔 Microcontroller MCU
LPC1754 P2 port UART2 problem
LPC1754's UART2 function, both port 0 and port 2 have this function, but why can't the UART2 of port 2 run? The UART2 initialization code is as follows. The UART2 pins of port 0 and port 2 are configu...
gstbetter NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2491  2306  403  2762  136  51  47  9  56  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号