TPAC250P datasheet, PDF - EEWORLD Datasheet

TPAC250P: DescriptionUNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES; File Size439KB，2 Pages; ManufacturerTotal Power International; Websitehttp://www.total-power.com/

Download Datasheet Compare View All

TPAC250P Overview

UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES

Preview

Download Datasheet

View All

UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP

CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING

SWITCHING POWER SUPPLIES

TPAC250P

SERIES

FEATURES:

250W 3U X 8HP EUROCARD PACKAGE

MEET IEC1000-3-2 HARMONIC CORRECTION

INTERNAL OR-ING DIODES FOR

N+1 REDUNDANCY

HOT-SWAPPABLE

THIRD-WIRE CURRENT SHARING

EMI MEET EN 55022 / FCC CLASS A

CE MARKING COMPLIANCE

FULLY COMPLIANT WITH PICMG

SPECIFICATION

INPUT SPECIFICATION

Input Voltage:

Typ. 90-264Vac.

Power Factor Correction:

Meet Harmonic Correction

IEC1000-3-2.Power Factor typ. 0.95-0.97.

Input Connector:

Positronic 47-pin PCIH47M400A1.

Input Frequency:

47-63Hz.

Inrush Current:

Less than 30A @ 230Vac.

Input Current:

2.8A @115Vac/1.4A @230Vac.

Dielectric Withstand:

Meet IEC950 regulation.

EMI:

Meet EN55022 / FCC Class A.

Hold-up Time:

5mS after power fail signal.

Earth Leakage:

Less than 0.5mA @230Vac.

Remote ON/OFF:

Available at [INH#] & [EN#] pins.

Power Fail Signal:

Available at [FAL#] pin.

Status LED:

<Green> means valid input voltage.

<Amber> means a critical fault.

Thermal Protection (OTP):

Installed NTC and

thermostat for thermal sensor at [DEG#] pin.

Power OK:

Installed at all outputs.

Leakage Current:

Typ. 0.5mA.

OUTPUT SPECIFICATION

Output Voltage:

See Ratings Chart.

Output Current:

See Ratings Chart.

Output Wattage:

Typ. 250W continuous.

Output Connector:

Positronic 47-pin PCIH47M400A1.

Line Regulation:

Typ. 0.1%.

Load Regulation:

Typ. ±1-2%.

Noise & Ripple:

Typ. 1% peak to peak or 50mV,

which is greater.

OVP:

Built-in at all outputs.

Adjustability:

Available at VO1,2&3.

Output Trim:

Electrical trim available at VO1 / VO2.[ADJ #].

Remote Sensing:

Available at VO1,VO2 & VO3.

Hot-Swap:

Available.

N+1 Redundancy:

Installed with internal OR-ing diodes

at all outputs for N+1 redundancy operation.

Current Sharing:

Third-wire current sharing at VO1,2 &3.

Power OK Signal:

Available for all output.

Over Current Protection (OCP):

Installed at each rail.

Overload Protection (OLP):

Fully protected against output

overload or short circuit. Typical 120% max. load.

Consult the factory for special OLP setting.

Operating Temperature:

0 to +50 °C at full load with

specified air flow. Derates linearly to 50% at +70 °C.

Storage Temperature:

-40 to +85 °C.

Temperature Coefficient:

Typ. ±0.02% / °C.

Cooling:

At least 20 cfm(600 lfm) moving air is required

to achieve full rating power 250W in a confined area.

Power Density:

4.58 Watts/ Cubic Inch.

GENERAL SPECIFICATION

Efficiency:

Typ. 78-79 %.

Switching Frequency:

120K Hz.

Circuit Topology:

Forward circuit.

Transient Response:

Peak transient less than 100mV and

recovers within 2mS after 25% load-change.

Safety Standard:

IEC60950 Class I.

Construction:

Eurocard 3U X 8HP X 160mm

CompactPCI format. Front Panel with

either Ordinary handle or Extractor handle.

Remark: All measurements are at nominal input, full load and +25°C unless otherwise specifications.

In application

TPAC250P Related Products

	TPAC250P	TPAC250P-490E	TPAC250P-490	TPAC250P-490O
Description	UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES	UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES	UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES	UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 250 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC250P SERIES

Recommended Resources

How to suppress power supply noise?

Electric drag control circuit diagram

slow starter circuit

Nokia mobile phone universal data cable circuit diagram

Single-phase AC motor forward and reverse control circuit

Voice control relay circuit diagram

Thermostat reference design based on TI SimpleLink wireless MCU: Most smart thermostat designers want to design a low-power, connected, microcontroller (MCU)-based smart thermostat that can securely connect a variety of sensors to the cloud for remote monitoring an...; Jacktang Wireless Connectivity

Recommend a CNC power supply circuit 0-30v 4A 5V 1A: At 0.1V, it carries 4A, and the voltage fluctuation between no-load and full-load is no more than 1mV, with an error of only 0.001V. The theoretical minimum step is 0.0073V and the actual step is 0.1V...; tonytong Power technology

Epitaxial wafer and LED chip detection issues: 1. Epitaxial wafer refers to the semiconductor film grown on the substrate. The film is mainly composed of three parts: P-type, quantum well, and N-type. The mainstream epitaxial material is gallium n...; 探路者 LED Zone

UCS module clock source setting when using CC430F5137 TimerA: [i=s] This post was last edited by langsunny on 2015-11-11 10:42 [/i] In setting TimerA, SMCLK was selected as the clock source. When configuring SMCLK to use dco as the source, it seems to be unsucce...; langsunny TI Technology Forum

【T Book Collection】Fault Tolerance and Redundancy Technology Related Special Issues: {:1_102:}The second batch of goods this week is here~~~~Forum friends who are interested in this technology, come and have a look~~Good information worth collecting~~ [url=https://download.eeworld.com...; tyw Download Centre

I would like to ask, does the STM32 ADC calibration adjust the absolute accuracy or the relative accuracy?: Is it possible to not measure VREFINT after calibration? From EEWORLD cooperation group: arm linux fpga embedded 0 (49900581) group leader: wangkj...; IC_WarMonkey stm32/stm8

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components