Note: Dual color temperature dimming is mainly achieved by changing the capacitance of C1 and C2, which results in different delays in VDD power-on time. Multiple capacitors are increased in sequence ...
Shouldn't the PN532's IRQ pin generate an interrupt when a card is received? I'm using the serial port mode, but why is it that even though I set the IRQ pin to be enabled, it doesn't work? I can read...
This section is the key content of this chapter. In this section, we need to master the formula method and the graphical method to calculate the Q point.Before learning, let's first understand a conce...
I don't know if you have ever encountered garbled characters in UBOOT when converting serial port to USB? I use the sbc2410 board, which works fine on Vivi, but garbled characters appear when starting...
I have been in the industry for more than four years and can use Verilog and C language proficiently; I have two years of experience in FPGA and ARM development; I am familiar with common EDA tools; M...
[i=s]This post was last edited by wsmysyn on 2018-7-29 10:09[/i] As the title: I was debugging FPGA recently and needed to burn the code into Flash; but the jic file was downloaded successfully but th...
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
I recently upgraded MDK to V5.25 and found that there are many libraries in the Managing Run-Time Environment. Compared with the past, it is much better, from the bottom-level driver to the upper-le...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
After we understand the use of libopencm3, we find that libopencm3 is only suitable for small projects. Its biggest feature is the convenience of USB. So when we configure large projects, is there a ...[Details]
Chip: STM32F107VCT6 Application Pin: THOUSANDS, RMII STM32CubeMX is very convenient to use ETH. The software comes with LWIP and configuration. This time, STM32F107VCT6+DP83848CVV is used. The MII a...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
In the Chinese automobile market, the trend of new energy vehicles and driverless cars is leading the transformation of China's automobile industry. As the world's largest automobile market, "Chinese...[Details]
Superconductors have physical properties such as zero resistance effect, Meissner effect and Josephson effect, which make them have broad application prospects and unparalleled advantages in many b...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
Temperature, humidity and irradiance are must-measure items in the photovoltaic industry. However, most of the current data collection is done by storing data in USB flash drives for offline analys...[Details]
In recent years, in order to meet the needs of social development, more and more companies have entered the fields of smart phones, artificial intelligence,
VR
, AR, etc. After seeing the d...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
sprintf is a function in the C language library that converts data types. There is a situation where In 51 MCU, define unsigned char temp; Then I want to use the serial port to print out temp in deci...[Details]