51761-10002410AA datasheet, PDF

Datasheet> All Categories > The connector> 51761-10002410AA

51761-10002410AA: DescriptionPower to the Board R/A REC POWERBLADE; CategoryThe connector; File Size91KB，13 Pages; ManufacturerFCI [First Components International]

Download Datasheet Parametric View All

51761-10002410AA Overview

Power to the Board R/A REC POWERBLADE

51761-10002410AA Parametric

Parameter Name	Attribute value
Product Attribute	Attribute Value
Manufacturer	FCI [First Components International]
Product Category	Power to the Board
RoHS	N
Contact Gender	Socket (Female)
Current Rating	30 A
Voltage Rating	2.5 kV Power, 1 kV Signal
Number of Positions	10 Power, 24 Signal
Mounting Style	Through Hole
Termination Style	Solder
Packaging	Tray
Housing Material	Thermoplastic
Mounting Angle	Right
Number of Rows	4 Row
Contact Arrangement	Signal/Power
Row Spacing	6.35 mm Power, 2.54 mm Signal
Insulation Resistance	10000 MOhms
Maximum Operating Temperature	+ 105 C
Minimum Operating Temperature	- 20 C
NumOfPackaging	1
Factory Pack Quantity	66

Preview

Download Datasheet

View All

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

1 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

1.0

OBJECTIVE

This specification defines the performance, test, quality and reliability requirements of the PwrBlade

Connector System.

2.0

SCOPE

This specification is applicable to the termination characteristics of separable right angle and vertical headers

when mated to the right angle and vertical receptacles.

3.0

GENERAL

If there is conflict between the product drawings and specifications, the drawing takes precedence.

This document is composed of the following sections:

Paragraph

1.0

2.0

3.0

4.0

5.0

5.1

5.2

5.3

5.4

5.5

6.0

7.0

8.0

9.0

9.1

9.2

9.3

9.4

9.5

9.6

10.0

Table 2

Title

OBJECTIVE

SCOPE

GENERAL

APPLICABLE DOCUMENTS

REQUIREMENTS

Qualification

Material

Finish

Design and construction

Workmanship

ELECTRICAL CHARACTERISTICS

MECHANICAL CHARACTERISTICS

ENVIRONMENTAL CONDITIONS

QUALITY ASSURANCE PROVISIONS

Equipment Calibration

Inspection Conditions

Sample Quality and Description

Acceptance

Qualification Testing

Re-qualification Testing

Reference Documents

Qualification Testing Matrix

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

5 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

7.3

Contact Retention – Individual power and signal contacts shall withstand an axial retention load of

13.4N [3 pound]. Individual signal receptacle contacts will withstand an axial load of 26.7N [6 pound]

minimum to seat further into housing.

a. Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity.

b. Test 30 contacts

c. As per MIL-STD-1344A, Method 2007.1.

7.4

Individual Pin Insertion/Retention Force - The force required to insert an individual compliant pin into

a plated through hole in a printed circuit board at a rate of 5.08mm [0.2 inch] per minute shall not

exceed 26.6N [6 pound] for signal receptacle contacts, 93.4N [21 pound] for signal header pins and

111.2N [25 pound] per tail for power contacts . The retention force in the axial direction opposite that

of insertion shall not be less than 6.7N [1.5 pound] for signal receptacle contacts, 13.4N [3 pound] for

signal header pins and 22.3N [5 pound] per tail for power contacts.

Table 3: Individual Pin Insertion/Retention Force table

Pwr contact

(per tail)

111.2N [25lbs]

22.3N [5lbs]

Signal contact

Rec Signal contact

26.6N [6lbs]

6.7N [1.5lbs]

Hdr Signal contact

93.4N [21lbs]

13.4N [3lbs]

Force spec.

Insertion force Maximum

Retention force Minimum

7.5

PCB Hole Deformation Radius

Power Contacts – cross-section parallel to board surface. Photograph and measure the hole

deformation (deformation on board material) radius at a point 0.254mm [0.010”] from the surface, and

the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole deformation

radius shall be no greater than0.0381mm [0.0015”] when measured from the drilled hole. The

absolute maximum deformation radius shall not exceed 0.0508mm [0.002”].

Signal Contacts

Signal Receptacle Contacts – Reference FCI BUS-12-111 – HPC Solderless (Press Fit) Right Angle

Receptacles

Signal Header Contacts – Same as the requirement for Power Contacts above

7.6

PCB Hole Wall Damage – Cross-section perpendicular to the board surface, and through the

compliant section wear track. Photograph and measure the copper thickness remaining between the

compliant section and the printed wiring board laminate. Include 10 holes. The minimum average (of

10 holes) copper thickness remaining between the compliant pin and the printed wiring board

laminate shall not be less than 0.00762mm [0.0003”]. In addition there shall be no copper cracks,

separations between conductive interfaces, or laminate-to-copper separations.

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

Recommended Resources

Transceiver external microphone circuit diagram

Collector JLC motor soft starter

Buck regulator circuit diagram using LM2579

Frequency multiplier counting circuit

Voltage stabilizing circuit with remote control on-off function

Digitally controlled gain amplifier circuit

Compiled successfully, but failed to run on the system recently: I successfully compiled it with PB, but when I downloaded it to the development version, I couldn’t boot it normally and the prompt was as follows: VBridge is not initialized! Bail out.. +CS8900:Drive...; bblfeng Embedded System

Quadcopter: [i=s]This post was last edited by paulhyde on 2014-9-15 03:32[/i] :call:...; lcb一不小心 Electronics Design Contest

TI's official SensorTag iBeaons app: It is said that after reading my last two posts, TI thought "It's amazing, SensorTag can be used like this!" Then they launched a new SensorTag firmware that supports iBeacons...:pleased: Haha, this i...; southwolf1813 Wireless Connectivity

TI Battery Fuel Monitoring Basics Training: [i=s] This post was last edited by dontium on 2015-1-23 11:47 [/i] [font=宋体][size=10.5pt]This manual introduces the basic knowledge of TI battery power monitoring, traditional battery power detection ...; 德州仪器 Analogue and Mixed Signal

Recommend: What brands of USB to parallel port conversion cables are more reliable?: Recommend: USB to parallel port conversion cable, what brands have high reliability? I mainly use Jtag debugging, thank you!...; shxhzxll Embedded System

Design of an extremely low power digital thermometer using MSP430: Temperature measurement is required in many places. When designing a temperature telemetry system, it is usually necessary to use a battery-powered, extremely low-power module. There are many traditio...; Aguilera Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components