a
FEATURES
High Input Sample Rate
67 MSPS Single Channel Real
33.5 MSPS Diversity Channel Real
33.5 MSPS Single Channel Complex
NCO Frequency Translation
Worst Spur Better than –100 dBc
Tuning Resolution Better than 0.02 Hz
2nd Order Cascaded Integrator Comb FIR Filter
Linear Phase, Fixed Coefficients
Programmable Decimation Rates: 2, 3 . . . 16
5th Order Cascaded Integrator Comb FIR Filter
Linear Phase, Fixed Coefficients
Programmable Decimation Rates: 1, 2, 3 . . . 32
Programmable Decimating RAM Coefficient FIR Filter
Up to 134 Million Taps per Second
256 20-Bit Programmable Coefficients
Programmable Decimation Rates: 1, 2, 3 . . . 32
Bidirectional Synchronization Circuitry
Phase Aligns NCOs
Synchronizes Data Output Clocks
Serial or Parallel Baseband Outputs
Pin Selectable Serial or Parallel
Serial Works with SHARC
®
, ADSP-21xx, Most Other
DSPs
16-Bit Parallel Port, Interleaved I and Q Outputs
Two Separate Control and Configuration Ports
Generic P Port, Serial Port
3.3 V Optimized CMOS Process
JTAG Boundary Scan
GENERAL DESCRIPTION
REAL,
DUAL REAL,
OR COMPLEX
INPUTS
67 MSPS Digital Receive
Signal Processor
AD6620
FUNCTIONAL BLOCK DIAGRAM
I
CIC
FILTERS
I
FIR
FILTER
I
OUTPUT
FORMAT
SERIAL OR
PARALLEL
OUTPUTS
Q
Q
Q
COS
–SIN
AD6620
COMPLEX
NCO
EXTERNAL
SYNC
CIRCUITRY
JTAG
PORT
P
OR SERIAL
CONTROL
both narrowband and wideband carriers to be extracted. The
RAM-based architecture allows easy reconfiguration for multi-
mode applications.
The decimating filters remove unwanted signals and noise from
the channel of interest. When the channel of interest occupies
less bandwidth than the input signal, this rejection of out-of-
band noise is called “processing gain.” By using large decimation
factors, this “processing gain” can improve the SNR of the
ADC by 36 dB or more. In addition, the programmable RAM
Coefficient filter allows antialiasing, matched filtering, and
static equalization functions to be combined in a single, cost-
effective filter.
The input port accepts a 16-bit Mantissa, a 3-bit Exponent,
and an A/B Select pin. These allow direct interfacing with the
AD6600, AD6640, AD6644, AD9042 and most other high-
speed ADCs. Three input modes are provided: Single Channel
Real, Single Channel Complex, and Diversity Channel Real.
When paired with an interleaved sampler such as the AD6600,
the AD6620 can process two data streams in the Diversity
Channel Real input mode. Each channel is processed with coher-
ent frequency translation and output sample clocks. In addition,
external synchronization pins are provided to facilitate coherent
frequency translation and output sample clocks among several
AD6620s. These features can ease the design of systems with
diversity antennas or antenna arrays.
Units are packaged in an 80-lead PQFP (plastic quad flatpack)
and specified to operate over the industrial temperature range
(–40°C to +85°C).
The AD6620 is a digital receiver with four cascaded signal-
processing elements: a frequency translator, two fixed-
coefficient decimating filters, and a programmable coefficient
decimating filter. All inputs are 3.3 V LVCMOS compatible.
All outputs are LVCMOS and 5 V TTL compatible.
As ADCs achieve higher sampling rates and dynamic range, it
becomes increasingly attractive to accomplish the final IF stage
of a receiver in the digital domain. Digital IF Processing is less
expensive, easier to manufacture, more accurate, and more
flexible than a comparable highly selective analog stage.
The AD6620 diversity channel decimating receiver is designed
to bridge the gap between high-speed ADCs and general pur-
pose DSPs. The high resolution NCO allows a single carrier to
be selected from a high speed data stream. High dynamic range
decimation filters with a wide range of decimation rates allow
SHARC is a registered trademark of Analog Devices, Inc.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
AD6620* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
DESIGN RESOURCES
•
AD6620 Material Declaration
•
PCN-PDN Information
•
Quality And Reliability
•
Symbols and Footprints
DOCUMENTATION
Application Notes
•
AN-502: Designing A Superheterodyne Receiver Using an
IF Sampling Diversity Chipset
•
AN-835: Understanding High Speed ADC Testing and
Evaluation
•
AN-851: A WiMax Double Downconversion IF Sampling
Receiver Design
Data Sheet
•
AD6620: 65 MSPS Digital Receive Signal Processor Data
Sheet
Product Highlight
• Introducing Digital Up/Down Converters: VersaCOMM™
Reconfigurable Digital Converters
DISCUSSIONS
View all AD6620 EngineerZone Discussions.
SAMPLE AND BUY
Visit the product page to see pricing options.
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
REFERENCE MATERIALS
Technical Articles
•
Basics of Designing a Digital Radio Receiver (Radio 101)
•
Designing a Super-Heterodyne Multi-Channel Digital
Receiver
•
Designing Filters with the AD6620
• Digital Up/Down Converters: VersaCOMM™ White Paper
•
Smart Partitioning Eyes 3G Basestation
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD6620
TABLE OF CONTENTS
ARCHITECTURE
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TIMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . 11
EXPLANATION OF TEST LEVELS . . . . . . . . . . . . . . . . 11
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . 12
PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 13
INPUT DATA PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OUTPUT DATA PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
FREQUENCY TRANSLATOR . . . . . . . . . . . . . . . . . . . . . 19
SECOND ORDER CASCADED INTEGRATOR
COMB FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FIFTH ORDER CASCADED INTEGRATOR
COMB FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
RAM COEFFICIENT FILTER . . . . . . . . . . . . . . . . . . . . . 25
CONTROL REGISTERS AND ON-CHIP RAM . . . . . . . 27
PROGRAMMING THE AD6620 . . . . . . . . . . . . . . . . . . . 30
ACCESS PROTOCOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
MICROPORT CONTROL . . . . . . . . . . . . . . . . . . . . . . . . 32
SERIAL PORT CONTROL . . . . . . . . . . . . . . . . . . . . . . . . 35
JTAG BOUNDARY SCAN . . . . . . . . . . . . . . . . . . . . . . . . 37
APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 44
As shown in Figure 1, the AD6620 has four main signal pro-
cessing stages: a Frequency Translator, two Cascaded Integrator
Comb FIR Filters (CIC2, CIC5), and a RAM Coefficient FIR
Filter (RCF). Multiple modes are supported for clocking data
into and out of the chip. Programming and control is accom-
plished via serial and microprocessor interfaces.
Input data to the chip may be real or complex. If the input data
is real, it may be clocked in as a single channel or interleaved
with a second channel. The two-channel input mode, called
Diversity Channel Real, is typically used in diversity receiver
applications. Input data is clocked in 16-bit parallel words,
IN[15:0]. This word may be combined with exponent input bits
EXP[2:0] when the AD6620 is being driven by floating-point or
gain-ranging analog-to-digital converters such as the AD6600.
Frequency translation is accomplished with a 32-bit complex
Numerically Controlled Oscillator (NCO). Real data entering
this stage is separated into in-phase (I) and quadrature (Q)
components. This stage translates the input signal from a digital
intermediate frequency (IF) to baseband. Phase and amplitude
dither may be enabled on-chip to improve spurious performance
of the NCO. A phase offset word is available to create a known
phase relationship between multiple AD6620s.
Following frequency translation is a fixed coefficient, high speed
decimating filter that reduces the sample rate by a program-
mable ratio between 2 and 16. This is a second order, cascaded
integrator comb FIR filter shown as CIC2 in Figure 1. (Note:
Decimation of 1 in CIC2 requires 2× or greater clock into
AD6620). The data rate into this stage equals the input data
rate, f
SAMP
. The data rate out of CIC2, f
SAMP2
, is determined by
the decimation factor, M
CIC2
.
RCF
3
16
INPUT
DATA
INTERLEAVE
DE-
INTERLEAVE
CIC5
M
CICS
f
SAMP5
23
23
f
SAMP2
COMPLEX
NCO
EXPLNV,
EXPOFF
RCF COEFFICIENTS
NUMBER OF TAPS
DECIMATE FACTOR
CIC2, CIC5
DECIMATE FACTORS ADDRESS OFFSET
f
SAMP
SCALE FACTORS
OUTPUT
NCO FREQUENCY
SCALE
PHASE OFFSET
FACTOR
DITHER
SYNC MASK
CONTROL REGISTERS
INPUT MODE
MICROPORT AND
REAL, DUAL, COMPLEX
SERIAL ACCESS
FIXED OR WITH EXPONENT
SYNC M/S
OUTPUT
SCALING, S
OUT
DV
OUT
I/Q
OUT
MULTIPLEXER
PARALLEL
16
SERIAL
A/B
OUT
MULTI-
PLEXER
I-RAM
256 18
C-RAM
256 20
Q-RAM
256 18
M
RCF
EXP[2:0]
IN[15:0]
FREQUENCY
3
TRANSLATOR
I 18
16
Q 18
EXP
SCALING
SCALING
CIC2
M
CICS
MULTI-
PLEXER
SCALING
PHASE
OFFSET
CLK
A/B
RESET
TIMING
SYNC NCO
SYNC CIC
SYNC RCF
SYNC
I/O
JTAG
TRST
TCK TMS
TDI
TDO
MICROPROCESSOR INTERFACE
D[7:0] A[2:0]
CS
R/W
DS DTACK
(W/R) (R/D) (RDY)
MODE PAR/SER
PARALLEL
OUTPUTS
AND
SERIAL I/O
16
OUT[15:0]
SCLK
SDI
SDO
SDFS
SDFE
SBM
WL[1:0]
AD
SDIV[3:0]
Figure 1. Block Diagram
–2–
REV. A
AD6620
Following CIC2 is the second fixed-coefficient decimating filter.
This filter, CIC5, further reduces the sample rate by a program-
mable ratio from 1 to 32. The data rate out of CIC5, f
SAMP5
, is
determined by the decimation factors of M
CIC5
and M
CIC2
.
Each CIC stage is a FIR filter whose response is defined by the
decimation rate. The purpose of these filters is to reduce the
data rate of the incoming signal so that the final filter stage, a FIR
RAM coefficient sum-of-products filter (RCF), can calculate
more taps per output. As shown in Figure 1, on-chip multiplex-
ers allow both CIC filters to be bypassed if a multirate clock
is used.
The fourth stage is a sum-of-products FIR filter with program-
mable 20-bit coefficients, and decimation rates programmable
from 1 to 32. The RAM Coefficient FIR Filter (RCF in Figure
1) can handle a maximum of 256 taps.
The overall filter response for the AD6620 is the composite of
all three cascaded decimating filters: CIC2, CIC5, and RCF. Each
successive filter stage is capable of narrower transition band-
widths but requires a greater number of CLK cycles to calculate
the output. More decimation in the first filter stage will minimize
overall power consumption. Data comes out via a parallel port
or a serial interface.
Figure 2 illustrates the basic function of the AD6620: to select
and filter a single channel from a wide input spectrum. The
frequency translator “tunes” the desired carrier to baseband.
CIC2 and CIC5 have fixed order responses; the RCF filter
provides the sharp transitions. More detail is provided in later
sections of the data sheet.
WIDEBAND INPUT SPECTRUM
C'
D'
SIGNAL OF INTEREST "IMAGE"
B'
A'
A
(–f
samp/
2 TO f
samp/
2)
SIGNAL OF
INTEREST
C
D
B
–f
S
/2
–3f
S
/8
–5f
S
/16
–f
S
/4
–3f
S
/16
–f
S
/8
–f
S
/16
DC
f
S
/16
f
S
/8
3f
S
/16
f
S
/4
5f
S
/16
3f
S
/8
f
S
/2
Figure 2a. Wideband Input Spectrum (e.g., 30 MHz from High-Speed ADC)
NCO "TUNES" SIGNAL TO BASEBAND
AFTER FREQUENCY TRANSLATION
A
B
C
D
D'
C'
B'
A'
–f
S
/2
–3f
S
/8
–5f
S
/16
–f
S
/4
–3f
S
/16
–f
S
/8
–f
S
/16
DC
f
S
/16
f
S
/8
3f
S
/16
f
S
/4
5f
S
/16
3f
S
/8
f
S
/2
Figure 2b. Frequency Translation (e.g., Single 1 MHz Channel Tuned to Baseband)
CIC2, CIC5, AND RCF
0
–10
–20
–30
–40
–50
dBc
–60
–70
–80
–90
–100
–110
–120
–130
FREQUENCY
Figure 2c. Baseband Signal is Decimated and Filtered by CIC2, CIC5, RCF
REV. A
–3–
AD6620–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
Parameter
VDD
T
AMBIENT
Test
Level
I
IV
Min
3.0
–40
AD6620AS
Typ
3.3
+25
Max
3.6
+85
Unit
V
°C
ELECTRICAL CHARACTERISTICS
Parameter (Conditions)
LOGIC INPUTS
1, 2, 3, 4, 5, 6, 7
(NOT 5 V TOLERANT)
Logic Compatibility
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Current
Logic “0” Current
Input Capacitance
LOGIC OUTPUTS
2, 4, 7, 8, 9, 10, 11
Logic Compatibility
Logic “1” Voltage (I
OH
= 0.5 mA)
Logic “0” Voltage (I
OL
= 1.0 mA)
IDD SUPPLY CURRENT
CLK = 20 MHz
12
CLK = 65 MHz
13
Reset Mode
14
POWER DISSIPATION
CLK = 20 MHz
12
CLK = 65 MHz
13
Reset Mode
14
Temp
Full
Full
Full
Full
Full
25°C
Full
Full
Full
Full
Full
Full
Full
Full
Full
Test
Level
Min
AD6620AS
Typ
3.3 V CMOS
I
I
I
I
V
2.0
–0.3
1
1
4
VDD + 0.3
0.8
10
10
V
V
µA
µA
pF
Max
Unit
I
I
V
I
I
V
I
I
2.4
3.3 V CMOS/TTL
VDD – 0.2
0.2
0.4
52
167
V
V
mA
mA
mA
mW
mW
mW
227
1
170
550
750
3.3
NOTES
1
Input-Only Pins: CLK,
RESET,
IN[15:0], EXP[2:0], A/B, PAR/SEL.
2
Bidirectional Pins: SYNC_NCO, SYNC_CIC, SYNC_RCF.
3
Microinterface Input Pins:
DS
(RD), R/W (WR),
CS.
4
Microinterface Bidirectional Pins: A[2:0], D[7:0].
5
JTAG Input Pins:
TRST,
TCK, TMS, TDI.
6
Serial Mode Input Pins: SDI, SBM, WL[1:0], AD, SDIV[3:0].
7
Serial Mode Bidirectional Pins: SCLK, SDFS.
8
Output Pins: OUT[15:0], DV
OUT
, A/B
OUT
, I/Q
OUT
.
9
Microinterface Output Pins:
DTACK
(RDY).
10
JTAG Output Pins: TDO.
11
Serial Mode Output Pins: SDO, SDFE.
12
Conditions for IDD @ 20 MHz. M
CIC2
= 2, M
CIC5
= 2, M
RCF
= 1, 4 RCF taps of alternating positive and negative full scale.
13
Conditions for IDD @ 65 MHz. M
CIC2
= 2, M
CIC5
= 2, M
RCF
= 1, 4 RCF taps of alternating positive and negative full scale.
14
Conditions for IDD in Reset (RESET = 0).
Specifications subject to change without notice.
–4–
REV. A
京公网安备 11010802033920号
EEWORLD
