Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= V
EN1
= V
EN2
= 3.6V, C
IN
= C1 = C2 = C
OUT
= 1µF, T
A
= -40°C to +85°C. Typical values are at T
A
= +25°C, unless otherwise
noted.) (Note 1)
PARAMETER
IN Operating Voltage
Undervoltage Lockout Threshold
Supply Current
Shutdown Supply Current
Soft-Start Completion Time
SET Bias Voltage
SET Leakage in Shutdown
SET Current Range
EN1 = EN2 = IN
SET to LED_ Current Ratio (I
LED
/I
SET
)
LED_ Current Accuracy
LED_ Current Matching
Maximum LED_ Sink Current
LED_ Dropout Voltage
LED_ Minimum Regulation Voltage (1.5x Mode)
LED Leakage in Shutdown
Maximum OUT Current
Open-Loop OUT Resistance
Switching Frequency
EN1, EN2 Logic High Voltage
EN1, EN2 Logic Low Voltage
EN1, EN2 Input Current
Thermal-Shutdown Threshold
V
IN
= 2.7V to 5.5V
V
IN
= 2.7V to 5.5V
V
EN
_ = GND or 5.5V, T
A
= +25°C
20°C hysteresis
0.01
160
1.6
0.4
1
I
SET
= 60µA
EN1 = IN, EN2 = GND
EN1 = GND, EN2 = IN
EN1 = EN2 = IN, R
SET
= 4.64kΩ, T
A
= 0°C to +85°C
I
SET
= 130µA, T
A
= 0°C to +85°C (Note 2)
I
SET
= 130µA, EN1 = EN2 = IN
I
SET
= 87µA (Note 3)
EN1 = EN2 = IN, I
SET
= 87µA
EN1 = EN2 = GND, V
LED
= 5.5V, T
A
= +25°C
V
IN
≥
3.4V, V
OUT
≥
3.9V, EN1 = EN2 = IN
1x mode (1 x V
IN
- V
OUT
) / I
OUT
1.5x mode (1.5 x V
IN
- V
OUT
) / I
OUT
1
120
1.5
10
100
25.9
EN1 = EN2 = GND, T
A
= +25°C
40
190
58
19.5
219
66
22
±0.6
±0.2
28
40
150
0.01
80
200
1
0.570
V
IN
rising or falling, 35mV hysteresis
Switching, no load, I
SET
= 130µA
EN1 = EN2 = OUT = GND, T
A
= +25°C
CONDITIONS
MIN
2.7
2.25
2.45
2
0.1
2.1
0.6
0.01
0.630
1
130
245
74
25.0
%
%
mA
mV
mV
µA
mA
Ω
MHz
V
V
µA
°C
A/A
TYP
MAX
5.5
2.60
4
10
UNITS
V
V
mA
µA
ms
V
µA
µA
Note 1:
Specifications to -40°C are guaranteed by design and not production tested.
Note 2:
LED_ current matching is defined as: (I
LED
- I
AVG
) / I
AVG
.
Note 3:
Dropout voltage is defined as the LED_ to GND voltage at which the LED_ current drops 10% from the value at V
[font=Arial][size=2]1. Experimental Task (1) When the machine is turned on, the time displayed is 12:00:00 and the timing starts; (2) P0.0/AD0 controls the adjustment of "seconds", and each press adds...
Electric shock is caused by the power supply forming a loop through the human body, and the energy of the current destroys the original bioelectric order in the human body, resulting in destructive re...
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
introduction
In recent years, with the increasing number of high-rise buildings, the demand for elevators has also increased. Currently, the elevators we use most often use LED dot array displ...[Details]
ESD protection diodes are specialized for small-signal ESD protection or surge protection TVS arrays, often used for multi-circuit protection. Their small package size, low on-state voltage, high i...[Details]
EVTank predicts that all-solid-state batteries will achieve small-scale mass production in 2027 and large-scale shipments by 2030. Global solid-state battery shipments will reach 614.1GWh, of which...[Details]
Deep in the laboratory, a seemingly ordinary piece
of
battery
material
was fed into the China Advanced Research Reactor (CARR). Scientists activated the neutron depth profiling device,...[Details]
Challenges come from multiple dimensions, and data centers on wheels require more rigorous testing.
Comparing the past, present, and future of automobiles, one clear trend emerges: cars ...[Details]
Preface
Embedded systems have been widely used in mobile phones, wristbands, tablet computers, and other devices. However, due to the limited processing performance of their central processing...[Details]
From smartwatches to portable health and fitness trackers, wearable devices are increasingly transforming every aspect of our daily lives. The desktop computer revolution of the 1980s ushered in an...[Details]
1. Introduction to power amplifier circuit
1. Generally speaking, the main function of a power amplifier circuit is to allow the load to obtain maximum power without distorting the signal or c...[Details]
On August 8, PetroChina Southwest Oil & Gas Field Company's 35kV Zhouping Line centralized battery energy storage system successfully completed a 24/7 trial run, achieving full compliance with all ...[Details]
Although everyone has their own unique approach to PLC programming, the ultimate model is the same. This article uses the simple ladder diagram programming method of Mitsubishi PLC as an example to...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
