5KP11A-G datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Discrete semiconductor> diode> 5KP11A-G

5KP11A-G: DescriptionESD Suppressors / TVS Diodes 5000W VRWM=11V,Unidi; CategoryDiscrete semiconductor diode; File Size60KB，5 Pages; ManufacturerComchip Technology; Websitehttp://www.comchiptech.com/; Environmental Compliance

Download Datasheet Parametric View All

5KP11A-G Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	5KP11A-G	-	-	View	Buy Now

5KP11A-G Overview

ESD Suppressors / TVS Diodes 5000W VRWM=11V,Unidi

5KP11A-G Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Comchip Technology
Reach Compliance Code	compliant
ECCN code	EAR99
Breakdown voltage nominal value	12.85 V
Maximum clamping voltage	18.2 V
Diode type	TRANS VOLTAGE SUPPRESSOR DIODE
Peak Reflow Temperature (Celsius)	NOT SPECIFIED
polarity	UNIDIRECTIONAL
Maximum repetitive peak reverse voltage	11 V
surface mount	NO
Maximum time at peak reflow temperature	NOT SPECIFIED

Preview

Download Datasheet

View All

5000W Transient Voltage Suppressor

COMCHIP

SMD Diodes Specialist

5KP-G Series

Stand-off Voltage: 6.8V ~ 220V

Power Dissipation: 5000 Watts

RoHS Device

Features

-Glass passivated chip.

0.052(1.32)

R-6

-Low leakage.

-Uni and Bidirection unit.

-Excellent clamping capability.

-The plastic material has UL recognition 94V-0.

-Fast response time.

0.048(1.22)

1.0(25.4)

MIN.

DIA.

0.360(9.14)

0.340(8.64)

Mechanical Data

-Case: Molded plastic R-6

-Polarity: By cathode band denotes uni-directional

device, none cathode band denotes bi-directional

device

-Weight: 2.1 grams

1.0(25.4)

MIN.

0.360(9.14)

0.340(8.64)

DIA.

Dimensions in inches and (millimeter)

Maximum Ratings and Electrical Characteristics

Rating at 25 C ambient temperature unless otherwise specified.

Single phase, half wave, 60Hz, resistive or inductive loaded.

For capacitive load, derated current by 20%.

Parameter

Peak power dissipation with a 10/1000μs

waveform (Note 1)

Peak pulse current with a 10/1000μs waveform

(Note 1)

Power dissipation on infinite heatsink at T

=75 C

Peak forward surge current, 8.3ms single

half sine-wave unidirectional only (Note 2)

Maximum instantaneous forward voltage at

100A for uni-directional devices only (Note 3)

Operating junction and storage temperature

range

NTOES:

Symbol

Value

5000

Unit

See Next Table

8.0

FSM

500

3.5 / 5.0

, T

STG

-55 to +150

(1) Non-repetitive current pulse, per fig.5 and derated above T

=25 C per fig. 1.

(2) Measured on 8.3 ms single half sine wave of equivalent square wave,duty cycle=4 pulses per minute maximum.

(3) V

<3.5V for devices of V

<200V and V

5.0V for devices of V

201V

REV:B

QW-BTV08

Page 1

Recommended Resources

Fuse protection circuit one a

Temperature frequency conversion circuit

monostable circuit

Light emitting diode tube zero shot and display circuit

Key pulse reset circuit

High gain broadband combination amplifier circuit

Looking for partners, about arm 9200: Due to the shortened project schedule, I am looking for a partner. The general situation is as follows: the board has been made, it can be started normally, Linux can also run, and I have made some dr...; sen234 ARM Technology

【Book Collection】Demonstration Tutorial on Basic Engineering Test Technology: ...; wzt Test/Measurement

2410 or 2440 development board with WIFI module, there are: As the title says, I want to develop a small device based on WIFI, but I can't find a 2410 or 2440 development board with WIFI function. There are other ARM11 ones, but they are not suitable. I only n...; nishitamade Embedded System

PT6311.pdf: A brief introduction to the PT6311 chip is very good ....; rain RF/Wirelessly

The process of WEBENCH design + FPGA multi-power design under the guidance of WEBENCH (2): [i=s]This post was last edited by Diguapatch on 2014-8-18 18:21[/i] The webench online design software has a multi-power design solution specifically for FPGAs and microprocessors. The mainstream manu...; 地瓜patch Analogue and Mixed Signal

Asking for advice on the LT1248 chip problem in the PFC circuit: My PFC circuit uses LT1248 chip, output 500W, followed by a half-bridge circuit output 36V14A, the half-bridge is adjusted fine, but there is a noise on the PFC side after loading, the bigger the load...; gyf20022 Analog electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components