BC566005FREQ datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> oscillator> BC566005FREQ

BC566005FREQ: DescriptionCMOS Output Clock Oscillator, 2MHz Min, 45MHz Max; CategoryPassive components oscillator; File Size34KB，2 Pages; ManufacturerCorning Frequency Control Inc

Download Datasheet Parametric View All

BC566005FREQ Overview

CMOS Output Clock Oscillator, 2MHz Min, 45MHz Max

BC566005FREQ Parametric

Parameter Name	Attribute value
Maker	Corning Frequency Control Inc
Reach Compliance Code	unknown
Maximum control voltage	4.5 V
Minimum control voltage	0.5 V
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	50 ppm
frequency stability	25%
Manufacturer's serial number	BC
Installation features	SURFACE MOUNT
Maximum operating frequency	45 MHz
Minimum operating frequency	2 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	CMOS
Output load	15 pF
physical size	7.5mm x 5.2mm x 2mm
Nominal supply voltage	5 V
surface mount	YES
maximum symmetry	40/60 %
Base Number Matches	1

Preview

Download Datasheet

View All

Typical Applications

Telecommunication

VCXO

Features

5x7 Ceramic Oscillator

Frequency range

Frequency stabilities

Parameter

Code I

2 MHz – 45 MHz

Frequency stability

Operating temp range

100 ppm

50 ppm

25 ppm

0....70 °C

Frequency tuning

Parameter

Code II

Value

Condition

Electrical frequency control

Voltage range

Pulling slope

> 50ppm

>100 ppm

0.5V to 4.5V

0.15V to 3.15V

Positive

@ V

=5V

@ V

=3.3V

RF output

Parameter

Value

Condition

Signal

Load

Duty cycle

CMOS

15pF

40/60%

Note 1

@ Vs/2

Supply Voltage

Parameter

Code III

Value

Condition

Supply voltage (Vs)

Power consumption steady state

Supply voltage (Vs)

Power consumption steady state

5V ± 5%

< 25 mA

< 40 mA

3.3V ± 5%

< 15 mA

< 20 mA

< 20 MHz

< 40 MHz

< 20 MHz

< 40 MHz

Additional parameters

Parameter

Frame Specification

Value

Condition

TQA 9000

Corning Frequency Control • Worldwide Data Book 2001

v1.0. 2000-10-20

Corning Frequency Control Inc.

• 100 Watts Street • Mt. Holly Springs, PA 17065 • Tel 1-717-486-3411 • Fax 1-717-486-5920 • www.corningfrequency.com

Tele Quarz GmbH & Co. KG

• Landstrasse • D-74924 Neckarbischofsheim, Germany • Tel +49-7268-801-0 • Fax +49-07268-801-281 • www.telequarz.de

1/2

Recommended Resources

ZTD-3 type modulated medium frequency electrotherapy machine circuit

Human body sensor alarm 2

900W full wave circuit

Power frequency induction furnace thyristor voltage regulation power supply control circuit

555 Sun brand car alarm circuit

Wireless alarm system using audio coding

DLP3010 Evaluation Kit "Appears"!: DLP3010 evaluation kit "appeared"! Sent from Shanghai yesterday!Attachments: USB cable, HDMI cable, you need to find a 5V, 15W power supply!...; 蓝雨夜 Analogue and Mixed Signal

Please write a C program: The following figure shows the two ports P0 and P1 of the (51) single-chip microcomputer. Each output pin of P0 is connected to the input of a three-state gate, for a total of 8 three-state gates. The...; lixuan62 MCU

Please ask for help on the power supply of EPD (electrophoretic display) panel.: Brief introduction of EPD technology: Electrophoretic display technology is to encapsulate black and white charged particles in a microcellular droplet structure (as shown below), and the external ele...; liutogo Analogue and Mixed Signal

How to turn off the ringtone: Is there any way to turn off the incoming call ringtone, while still being able to hear the music of the video, and not rejecting or answering the call? I just want to insert a video when a call comes...; hbsunny78 Embedded System

The stepper motor controlled by PLC always makes noise, please help me!: I am a beginner in PLC. I use a program left by a senior to control a stepper motor. Why is it that when I use a normally closed contact for input terminal I0.1, the motor can rotate, but when I chang...; eeleader-mcu Industrial Control Electronics

Ethernet and serial bootloader updates can be used: The Ethernet and serial port bootloader updates can be used, but there is a tricky problem. In the serial port boot_series, it is determined by pulApp = (unsigned long *)APP_START_ADDRESS; if((pulApp[...; chen20061084 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components