SIDACtor
®
Protection Thyristors
SLIC Protection
Battrax
®
Single Port Positive/Negative - MS-013
Description
The Single Port Positive/Negative Battrax Series are
programmable SIDACtor
®
devices designed to protect
SLICs (Subscriber Line Interface Circuit) from damaging
overvoltage transients.
This series is designed specifically to protect SLIC devices
utilizing positive and negative ringing signals. This one
device will protect a single port.
Features and Benefits
Low voltage overshoot
Low on-state voltage
Agency Approvals
Agency
Agency File Number
E133083
Battrax
®
Single Port Pos/Neg
Low Capacitance
Positive and negative
ringing compatible
Single-port protect
Gate trgger tracking
device
Does not degrade with
use
Fails short circuit when
surged in excess of
ratings
Applicable Global Standards
6
5
4
Pinout Designation
1
2
3
TIA-968-A
ITU K.20/21 Enhanced
Level
ITU K.20/21 Basic Level
GR 1089 Inter-building
GR 1089 Intra-building
IEC 61000-4-5
YD/T 1082
YD/T 993
YD/T 950
Schematic Symbol
(T) 1
6 (Ground)
(-V
REF
) 2
5 (+V
REF
)
(R) 3
4 (Ground)
Electrical Characteristics
V
DRM
@l
DRM
=5μA
V min
B3104UCLxx
B3164UCLxx
B3204UCLxx
B3104UC I±V
REF
B3164UC I±V
REF
B3204UC I±V
REF
V
S
@100V/μs
V max
I±V
REF
I±V
REF
I±V
REF
I
H
I
S
I
T
A max
2.2
2.2
2.2
V
T
@I
T
=2.2 Amps
V max
4
4
4
Capacitance*
pF min pF max
30
30
30
200
200
200
Part Number
Marking
mA min mA max
100
160
200
100
100
100
Notes:
- Absolute maximum ratings measured at T
A
= 25ºC (unless otherwise noted).
- Devices are bi-directional
- All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 4 & 6) and
Ring (pin 3) to Ground (pin 4 & 6)
- V
REF
Max Value for the negative Battrax is -200 V.
- V
REF
-
XX =
Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack).
* Off-state capacitance (C
O
) is measured across pins 1 & 4,6 and 3 & 4,6
at 1 MHz with a 2V bias.
122
© 2009 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SIDACtor
®
Protection Thyristors
SLIC Protection
Surge Ratings
I
PP
Series
0.2x310
1
0.5x700
2
A min
C
Notes:
1 Current waveform in μs
2 Voltage waveform in μs
- Peak pulse current rating (I
PP
) is repetitive and guaranteed for the life of the product.
rating assumes V
REF
- I
PP
PP
- The device must initially be in thermal equilibrium with -40°C < T
J
<
2x10
1
2x10
2
A min
500
8x20
1
1.2x50
2
A min
400
10x160
1
10x160
2
A min
200
10x560
1
10x560
2
A min
150
5x320
1
9x720
2
A min
200
10x360
1
10x360
2
A min
175
10x1000
1
10x1000
2
A min
100
5x310
1
10x700
2
A min
200
I
TSM
50/60
Hz
A min
50
di/dt
A/μs max
500
50
Thermal Considerations
Package
Modified MS-013
6
5
4
1
2
3
Symbol
T
J
T
S
R
0JA
Parameter
Operating Junction Temperature Range
Storage Temperature Range
Thermal Resistance: Junction to Ambient
Value
Unit
°C
°C
60
°C/W
V-I Characteristics
+I
I
H
V
S
-V
REF
V
DRM
V
T
I
PP
V
DRM
V
REF
I
S
I
DRM
+V
t
r
x t
d
Pulse Waveform
V
S
I
PP
– Peak Pulse Current – %I
PP
100
Peak
Value
t
r
= rise time to peak value
t
d
= decay time to half value
Waveform = t
r
x t
d
-V
I
DRM
I
S
I
T
I
PP
-I
I
H
50
Half Value
0
0
t
r
t
d
t – Time (μs)
Normalized V
S
Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
2.0
14
Percent of V
S
Change – %
12
10
8
6
4
2
0
-4
-6
-8
-40 -20
0
20 40 60 80 100 120 140 160
I
H
(T
C
= 25ºC)
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
-40
-20
0
20
40
60
80
100 120 140 160
I
H
25 °C
25°C
Ratio of
Junction Temperature (T
J
) – °C
Case Temperature (T
C
) - ºC
© 2009 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
123
Battrax
®
Single Port Pos/Neg
SIDACtor
®
Protection Thyristors
SLIC Protection
Soldering Parameters
Reflow Condition
- Temperature Min (T
s(min)
)
Pb-Free assembly
(see Fig. 1)
Figure 1
T
P
Ramp-up
t
P
Critical Zone
T
L
to T
P
Pre Heat
- Temperature Max (T
s(max)
)
- Time (Min to Max) (t
s
)
60-180 secs.
Temperature
Average ramp up rate (Liquidus Temp (T
L
)
to peak)
T
S(max)
to T
L
- Ramp-up Rate
- Temperature (T
L
) (Liquidus)
- Temperature (t
L
)
T
L
T
S(max)
Preheat
3°C/sec. Max.
3°C/sec. Max.
60-150 secs.
t
L
Ramp-down
Battrax
®
Single Port Pos/Neg
Reflow
T
S(min)
t
S
Peak Temp (T
P
)
Time within
5°C
of actual Peak Temp (t
p
)
Ramp-down Rate
Time 25°C to Peak Temp (T
P
)
Do not exceed
30 secs. Max.
6°C/sec. Max.
8 min. Max.
25
time to peak temperature
(t 25ºC to peak)
Time
Physical Specifications
Lead Material
Terminal Finish
Body Material
Copper Alloy
100% Matte-Tin Plated
Environmental Specifications
High Temp Voltage
Blocking
80% Rated V
DRM
(V
DC
Peak
504 or 1008 hrs. MIL
-STD-750 (Method 1040)
JEDEC, JESD22-A-101
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
52 V
DC
JEDEC, JESD22-A-101
JEDEC, JESD22-A-101
-65°C, 1008 hrs.
10 cycles. MIL
-STD-750 (Method 1056) JEDEC,
JESD22-A-106
JEDEC, JESD22-A-102
Temp Cycling
UL recognized epoxy meeting flammability
classification 94V-0
Biased Temp &
Humidity
High Temp Storage
Low Temp Storage
Thermal Shock
Autoclave (Pressure
Cooker Test)
Resistance to Solder
Heat
Moisture Sensitivity
Level
Part Numbering
B3 xx
4
U C L xx
TYPE
B3: Dual (Positive & Negative
Battrax SIDACtor)
Part Marking
PACKING OPTIONS
RP: Reel Pack
TP: Tube Pack
XXXXXXX
XXXXX
Part Marking Code
(Refer to Electrical Characteristics Table)
RoHS COMPLIANT
HOLDING CURRENT
10: 100 mA
20: 200 mA
16: 160 mA
Date Code
I
PP
RATING
PACKAGE TYPE
CONSTRUCTION VARIABLE
124
© 2009 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SIDACtor
®
Protection Thyristors
SLIC Protection
Dimensions — MS-013
Dimensions
Pad Outline
C
0.138
(3.50)
E
0.059
(1.50)
0.065
(1.65)
0.460
(11.68)
Dimension are in inches
(and millimeters).
Inches
Min
0.360
0.352
0.400
0.043
0.047
0.293
0.289
0.089
0.041
0.020
0.133
Max
0.364
0.356
0.412
0.045
0.055
0.297
0.293
0.093
0.049
0.143
Millimeters
Min
9.14
8.94
10.16
1.09
1.19
7
.44
7
.34
2.26
1.04
0.51
3.38
Max
9.25
9.04
10.46
1.13
1.40
7
.54
7
.44
2.36
1.24
3.63
7º TYP
A
D
7º TYP
G
A
J
H
Burr Side
96º
4º
7º TYP
B
A
F
7º TYP
MIN Length
of Flat
K
Detail A
Mold Split
Line
BSC*
* BSC =
Basic Spacing
between
Centers
Packing Options
Package Type
Description
Modified MS-013 6-pin
Tape and Reel Pack
Quantity
Added Suffix
Industry Standard
1500
500
(50 per tube)
RP
TP
EIA-481-D
N/A
U
Modified MS-013 6-pin
Tube Pack
Tape and Reel Specification — MS-013
.157
(4.0)
.630
(16.0)
.512 (13.0) Arbor
Hole Dia.
.472
(12.0)
12.99
(330)
Dimensions are in inches
(and millimeters)
0.700
(17
.8)
Direction of Feed
Tube Pack Specification — MS-013
Message Location
.020 ± .005 WALL TYP.
(0.51 ± 0.13)
.108
(2.74)
.110
(2.79)
.045
(1.14)
90˚
.165
(4.19)
.310
(7.87)
6
Interior of the Tube
20.000 ± .030
(508.00 ± 0.76)
.005 A
.150
(3.81)
.225
(5.72)
.525
(13.34)
A
Dimensions are in inches
(and millimeters)
125
© 2009 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Battrax
®
Single Port Pos/Neg
A
B
C
D
E
F
G
H
J
K
BSC*
京公网安备 11010802033920号
EEWORLD
