(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
1,000 m/s
2
(Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 1.5 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 1.5 mm
Min. 2×10
6
Min. 10
5
(at resistive load)
Ambient temperature: –40°C to +85°C
–40°F to +185°F;
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 times/min. (at nominal switching capacity)
Approx. 17 g
.60 oz,
Approx. 15 g
.53 oz
(PCB type)
Temperature rise (coil)
Surge breakdown voltage*
2
(Between contact and coil) (Initial)
Operate time (at nominal voltage) (at 20°C
68°F)
Release time (at nominal voltage) (at 20°C
68°F)
Shock resistance
Functional
Destructive
Functional
Mechanical
characteristics
Vibration resistance
Expected life
Destructive
Mechanical (at 180 times/min.)
Electrical (at 20 times/min.)
Conditions for operation, transport and storage*
3
Max. operating speed
Conditions
Unit weight
* Specifications will vary with foreign standards certification ratings.
Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2×50µs
according to JEC-212-1981
*3. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
REFERENCE DATA
1.-(1) Coil temperature rise (400mW type)
Sample: ALE14B12, 6 pcs.
Point measured: coil inside
Ambient temperature: 25°C
77°F,
85°C
185°F
60
25°C
85°C
16A
12A
0A
16A
12A
0A
1.-(2) Coil temperature rise (200mW type)
Sample: ALE74B12, 6 pcs.
Point measured: coil inside
Ambient temperature: 23.7°C
74.66°F,
85°C
185°F
30
23.7°C
85°C
16A
2. Life curve
100
50
Temperature rise,
°C
25
16A
0A
Temperature rise,
°C
40
20
250V AC resistive load
Life,
×10
4
0A
30
15
10
20
10
10
5
0
0
80
100
Coil applied voltage, %V
145
0
0
80
100
Coil applied voltage, %V
145
1
0
2
4
6
8
10
12
14
16
Contact current, A
Panasonic Corporation Automation Controls Business Division
Some people boast that even if the software they wrote is decrypted by others, the pass rate of burning with the decrypted code is only 80% (and this pass rate can be determined when writing the progr...
[i=s]This post was last edited by dontium on 2015-1-23 11:11[/i] [align=left][font=宋体][size=4] Chapter 5 introduces the introduction to noise measurement and introduces three instruments for measuring...
This is a problem I encountered when observing the RTL view when doing an experiment on digital tubes. I don't know what the red symbols in the picture mean? Please explain it to me....
I chose the vxworks course, but I was busy with other things for the whole semester. I have a few days left to hand in my homework. I am in a hurry. I sincerely need help from experts. Price is negoti...
[i=s] This post was last edited by paulhyde on 2014-9-15 09:42 [/i]Optimize the application of matlab to find the minimum and maximum values, etc. to reduce the calculation pressure [free][/free] [[i]...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
