EEWORLDEEWORLDEEWORLD

Part Number

Search

PR5-2.29KDI

Description
RESISTOR, METAL FILM, 0.5W, 0.5%, 25ppm, 2290ohm, THROUGH HOLE MOUNT, AXIAL LEADED
CategoryPassive components    The resistor   
File Size388KB,2 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PR5-2.29KDI Overview

RESISTOR, METAL FILM, 0.5W, 0.5%, 25ppm, 2290ohm, THROUGH HOLE MOUNT, AXIAL LEADED

PR5-2.29KDI Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1768399038
package instruction,
Reach Compliance Codecompliant
Country Of OriginMainland China
ECCN codeEAR99
YTEOL6.75
Other featuresPRECISION
JESD-609 codee3
Manufacturer's serial numberPR
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package shapeTUBULAR PACKAGE
method of packingAMMO PACK
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance2290 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyMETAL FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin (Sn) - hot dipped
Terminal shapeWIRE
Tolerance0.5%
Operating Voltage350 V
Precision Metal
Film Resistors
PR series
Welwyn Components
Low cost precision resistors
Tolerances down to ±0.1%
TCR down to 15ppm/°C
Electrical Data
PR4
Power rating at 70°C
Resistance range
Limiting element voltage
TCR*
Resistance tolerance
Standard values
Thermal impedance
Ambient temperature range
°C/watt
°C
watts
ohms
volts
ppm/°C
%
0.25
100R – 240K
250
25
0.1, 0.25, 0.5, 1
E192
140
-55 to 155
PR5
0.5
100R – 1M
350
25
0.1, 0.25, 0.5, 1
E192
112
*15ppm/°C available by request
Physical Data
Dimensions (mm) & Weight (g)
PCB
Min.
mounting bend
radius
Wt.nom
0.6
1.2
0.3
0.5
d
D
L
f
Type
PR4
PR5
L Max
6.2
9.0
D Max
2.5
3.6
f min
21
19.6
d nom
0.6
0.8
centres
10.2
12.7
Construction
The resistance element is a precisely controlled thin film of
metal alloy sputtered on to a high purity ceramic core,
protected by a moisture-resistant, high dielectric strength
coating applied so that terminations remain completely clear.
This permits a well defined body length (clean lead to clean
lead dimension L).
Terminations
Material
Strength
Solderability
Solder-coated copper wire.
The terminations meet the requirements of
IEC 68.2.21
The terminations meet the requirements of
IEC 115-1, Clause 4.17.3.2
Marking
Resistors are colour coded with 5 bands. IEC 62 colours are
used.
Solvent Resistance
The body protection and marking are resistant to all normal
industrial cleaning solvents suitable for printed circuits.
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyn’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
Issue C · 04.03
© Welwyn Components Limited
· Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 · Facsimile: +44 (0) 1670 829465 · Email: info@welwyn-tt.com · Website: www.welwyn-tt.com
182
[Transfer] Microstrip and Stripline Design
Much has been written about how to terminate PCB trace characteristic impedance to avoid signal reflections. However, when to properly apply transmission line techniques is less clear. A proven guidel...
dontium RF/Wirelessly
Problems with Labview and USB device communication
Hey guys, I'm making a tool to test the consistency of a particle sensor. The main chip of the tool uses STM32F407. The MCU collects the data from the sensor and uploads it to the PC via USB. Labview ...
woody_chen MCU
SPI issues with STM32F103
I would like to ask you seniors, STM32F103 SPI problem STM as slave (NXP's LPC2294 as host to communicate with it) (urgent) I encountered a problem in adjusting the SPI of STM32F103. I have been adjus...
lg324 stm32/stm8
[AB32VG1 development board review] TF card and file reading and writing applications
The AB32VG1 development board is equipped with a TF card slot, and its interface is shown in Figure 2. When a TF card is inserted, file-level operations can be performed with the cooperation of the fi...
jinglixixi Domestic Chip Exchange
The parasitic diode voltage drop problem of the PMOS tube in this charging circuit
As shown in the figure, this is a commonly used charging circuit. The PMOS tube model used in Q411 is CJ3401, and the specifications are as shown in the figure. The working principle is that when 5V i...
elec32156 Analog electronics
I would like to ask: Why can't I open the link in mmio under wince?
The error is as follows: error LNK2019: unresolved external symbol "struct HMMIO__ * __cdecl mmioOpen(char *,struct _MMIOINFO *,unsigned long)" (?mmioOpen@@YAPAUHMMIO__@@PADPAU_MMIOINFO@@K@Z) referenc...
jingyu527 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1446  1782  1113  1886  542  30  36  23  38  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号