Note: A 0.01 Ohm addition to be added to the performance of all resistors <10 Ohms.
Pulse Performance Data
Lightning Surge
Lightning surge resistors are tested in accordance with IEC 60 115-1 using both 1.2/50µs and 10/700µs pulse shapes. 10 pulses are applied. The limit of
acceptance is a shift in resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
The single impulse graph is the result of 50 impulses of rectangular shape applied at one minute intervals. The limit of acceptance was a shift in
resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Continuous Load Due to Repetitive Pulses
The continuous load graph was obtained by applying repetitive rectangular pulses where the pulse period was adjusted so that the average
power dissipated in the resistor was equal to its rated power at 70°C. Again the limit of acceptance was a shift in resistance of less than 1% from the
initial value
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
I am using the POWERPC interrupt MPC5200B vxworks operating system. When doing interrupt nesting test, I found that the 5200 interrupt priority mechanism often does not work. Test method: Set the prio...
Good morning, everyone. I want to engage in the development of automotive electronics recently, mainly for automotive smart interior and seats. I am a computer major and have a good understanding of c...
I am using Android to make a Bluetooth communication device. There are two interfaces that need to be switched. For the sake of convenience, let's say there are two interfaces, A and B. Interface A ha...
As shown in the figure, V0=Ip*R. Is the gain calculated like this? G=20lgR? I feel that the resistor R is the amplification factor, so it should be correct to calculate it this way. According to the g...
Digital-to-analog converters (ADCs) provide the critical conversion of analog signals to digital signals in many systems. They perform amplitude quantization of an analog input signal to a binary fini...[Details]
How can we get the highest performance from an A/D converter? The obvious answer is to use good design and board layout, but there are other techniques that can be used to improve performance. We can ...[Details]
Magnetic resonance imaging (MRI) systems for medical and scientific applications require a high-performance, high-power inductor capable of establishing a uniform, strong magnetic field. Transverse el...[Details]
Sensors have made inroads into automotive, medical, industrial and aerospace applications. But you may not see anything changing yet. Growing demands for safety, convenience, entertainment and efficie...[Details]
In response to a series of problems caused by the backwardness of traditional water meters, the Ministry of Construction of China has proposed the requirement of "three meters per household" for ur...[Details]
Lithium-ion battery is a widely used rechargeable battery. It has the advantages of high single-cell operating voltage, small size, light weight, high energy density, long cycle life, rapid full ch...[Details]
To ensure the success of China's TD-SCDMA network commercialization, operators and equipment suppliers need to conduct a large number of tests on networked equipment, among which RF testing is...[Details]
As microcontrollers become less expensive and more powerful, electrical designers are finding it more cost-effective to use multiple small controllers in both single-board and multi-board systems. ...[Details]
E6601A is Agilent's new generation of comprehensive tester platform, designed to provide low-cost calibration solutions for mobile phone manufacturers. It uses an open Windows® XP platform, allowi...[Details]
introduction
In engineering practice, ultrasonic waves are often used to measure distances because of their strong directivity, slow energy consumption, and long propagation distance in th...[Details]
Overview
In recent years, the vigorous development of integrated circuits has created a huge space for the research and application of digital circuits. FPGA has low power consumption, high re...[Details]
Introduction
The MAX2116 P1db data is measured at specific combinations of RF and baseband gain over the adjustable range of these two gains. These data can be used to select gain control se...[Details]
Fetal monitoring is an important means to ensure the safety of perinatal mothers and fetuses and achieve eugenics. Intelligent fetal monitoring is a monitoring method that analyzes the health stat...[Details]
1 Introduction
Generally, when transmitting information over short distances through electrical signals, baseband signals can be directly transmitted. However, over long distances, baseban...[Details]
introduction
Every friend who has been in contact with PC since the 286 era must have deeply experienced the convenience brought to our lives and work by the leaps and bounds of comput...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
