1241.2204.6.0.7 datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> 1241.2204.6.0.7

1241.2204.6.0.7: DescriptionPushbutton Switch, DPST, On-(off), Momentary, 0.2A, 50VDC, 1 PCB Hole Cnt, Solder Terminal, Surface Mount-right Angle; CategoryMechanical and electronic products switch; File Size157KB，10 Pages; ManufacturerSCHURTER; Websitehttp://www.schurterinc.com/; Environmental Compliance

Download Datasheet Parametric View All

1241.2204.6.0.7 Overview

Pushbutton Switch, DPST, On-(off), Momentary, 0.2A, 50VDC, 1 PCB Hole Cnt, Solder Terminal, Surface Mount-right Angle

1241.2204.6.0.7 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	SCHURTER
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator angle
Actuator length	0.346 inch
Actuator material	POLYAMIDE
Actuator type	PUSHBUTTON
Other features	NON LUMINOUS, W/LARGE BUTTON
body width	7.493 mm
body height	20.4978 mm
Body length or diameter	9.652 mm
Casing diameter	0.295 inch
Nozzle length	0.118 inch
Casing type	UNTHREADED
center contact material	BERYLLIUM COPPER
Center contact plating	SILVER
Contact (AC) maximum rated R load	0.2A@60VAC
Maximum contact current (AC)	0.2 A
Maximum contact current (DC)	0.2 A
Contact (DC) maximum rated R load	0.2A@50VDC
Contact function	ON-(OFF)
Contact resistance	0.05 mΩ
Maximum contact voltage (AC)	60 V
Maximum contact voltage (DC)	50 V
Electrical life	500000 Cycle(s)
End contact material	BERYLLIUM COPPER
End contact plating	SILVER
Insulation resistance	10000000000 Ω
insulator material	POLYAMIDE
JESD-609 code	e3
Manufacturer's serial number	HDT
Installation features	SURFACE MOUNT-RIGHT ANGLE
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
PCB hole count	1
surface mount	NO
Switch action	MOMENTARY
switch function	DPST
Switch type	PUSHBUTTON SWITCH
Terminal surface	Matte Tin (Sn)
Terminal length
Terminal material	BRASS
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

Switches in momentary action HDT and latching action

Models

Construction

Dimensions

Drilling diagram

Drilling diagramm

= 1,25mm

Circuit diagram

Z =

Drilling for pin location

fixed contact 1 pole

Small button:

cut out ø 8 mm

*Indication

area illuminated version

Large button:

cut out ø 10 mm

Drilling diagramm

= 1,25mm

Z =

Drilling for pin location

fixed contact 1 pole

Small button:

cut out ø 8 mm

*Indication

area illuminated version

Large button:

cut out ø 10 mm

Drilling diagramm

= 1,25mm

NO/NC

Z =

Drilling for pin location

fixed contact 1 pole

Small button:

cut out ø 8 mm

*Indication

area illuminated version

Large button:

cut out ø 10 mm

Printmount Line

Recommended Resources

Isolated temperature sensor

Working principle of series switching power supply (c)

Dimming desk lamp circuit three

Current Sensing Circuit Diagram for Supply Rail

LM339 fully automatic charger circuit

Gas pendulum tilt sensor circuit

Smart desk lamp made of single chip microcomputer: This is a smart desk lamp made with a microcontroller, take a look......; heyuanqian PCB Design

Opinions sought, wireless key tracker: Today I helped my mother find her keys again, and I was exhausted. My mother is old and has a bad memory. She has to look for her keys before going out. As an electronics expert, I think this is not a...; sjl2001 MCU

28335 SCI Communication Problem Summary: [size=5]When learning SCI communication, I thought it should not be difficult because I had experience with 51 serial ports. But in fact, it is not as easy as I imagined. [/size] [size=5] [/size] [siz...; 灞波儿奔 DSP and ARM Processors

Wireless Network Notes: In the Wi-Fi table, it mentions the frequency of the router/gateway, either 2.4 GHz or 5 GHz. It is recommended that an apartment or condo type housing setup should be 5 GHz to avoid any possible inte...; btty038 RF/Wirelessly

Looking for Proteus simulation example: I am currently learning microcontroller simulation, and I hope you can provide more information on this aspect. Thank you....; Essen Embedded System

DM648 network port abnormality caused by JTAG clock: A post about the abnormality of the DM648 network port. The final reason is that the JTAG TCLK is not pulled down. The following is part of the original post:We've been having problems with Ethernet c...; Jacktang DSP and ARM Processors

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components