SPECIFICATION CONTROL DRAWING
TITLE
44A412X
Date
TWO CONDUCTOR CABLE, JACKETED, LIGHTWEIGHT,
GENERAL PURPOSE, 600 VOLT
05-08-04
Revision
E
This specification sheet forms a part of the latest issue of Raychem Specification 44
COMPONENT WIRES - 44A011X
JACKET - RADIATION-CROSSLINKED,
MODIFIED PVF
2
TABLE I. CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
JACKET THICKNESS
(in.)
MINIMUM
NOMINAL
OUTSIDE DIAMETER
(in.)
NOMINAL
MAXIMUM
MAXIMUM
WEIGHT
(lb/1000 ft)
44A412X-26-*
44A412X-24-*
44A412X-22-*
44A412X-20-*
44A412X-18-*
44A412X-16-*
44A412X-14-*
44A412X-12-*
26
24
22
20
18
16
14
12
.005
.005
.005
.005
.005
.005
.005
.006
.007
.007
.007
.007
.007
.007
.007
.008
.082
.094
.108
.124
.144
.158
.192
.232
.087
.099
.114
.130
.150
.165
.199
.240
4.3
6.0
8.4
12.0
17.4
21.7
33.1
51.0
TABLE II. CABLE PERFORMANCE DETAILS
BEND TESTING
MANDREL DIAMETER
(inch) (± 3%)
ACCELERATED AGING
IMMERSION AND
LIFE CYCLE
COLD
BEND
WEIGHT
(lb) (± 3%)
ACCELERATED AGING
IMMERSION AND
LIFE CYCLE
COLD
BEND
PART NUMBER
1/
44A412X-26-*
44A412X-24-*
44A412X-22-*
44A412X-20-*
44A412X-18-*
44A412X-16-*
44A412X-14-*
44A412X-12-*
3.00
3.00
3.00
3.00
6.00
6.00
6.00
6.00
3.00
3.00
3.00
3.00
6.00
6.00
6.00
6.00
.250
.375
.375
.375
.500
.500
1.00
1.00
1.50
1.50
3.00
3.00
3.00
3.00
9.00
9.00
NOTE: Nominal values are for information only.
Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
Page 1 of 2
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
R
Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
SCD Number
SPECIFICATION CONTROL DRAWING
Page 2 of 2
44A412X
WIRE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C;
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 225 ± 2°C for 6 hours.
BLOCKING: 150 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute
FLAMMABILITY: 30 seconds (maximum); 3 in. (maximum);
no flaming of facial tissue.
JACKET COLOR: White preferred
JACKET CONCENTRICITY: 70% (minimum)
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 200% (minimum)
Tensile strength, 4000 lbf/in
2
(minimum)
LIFE CYCLE: 200 ± 3°C for 168 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
PART NUMBER
The "X" in the part numbers on page 1 shall be replaced by the applicable conductor material
designators as follows:
1 tin-coated copper
2 silver-coated copper
3 nickel-coated copper
4 silver-coated high strength copper alloy (AWG's 26 - 16 only)
6 nickel-coated high strength copper alloy (AWG's 26 - 20 only)
The "*" in the part numbers on page 1 shall be replaced by color code designators with a slash
separating the component wire colors and a dash separating the component wire colors from
the jacket color.
1/ Example: 20 Awg, tin-coated copper wires, black and brown component wires; white jacket:
44A4121-20-0/1-9
1/ See footer section on page 1
京公网安备 11010802033920号
EEWORLD
