EEWORLDEEWORLDEEWORLD

Part Number

Search

SO63-2-55-26-90

Description
SO63-2-55-26-90
CategoryThe connector   
File Size133KB,10 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

SO63-2-55-26-90 Online Shopping

Suppliers Part Number Price MOQ In stock  
SO63-2-55-26-90 - - View Buy Now

SO63-2-55-26-90 Overview

SO63-2-55-26-90

SO63-2-55-26-90 Parametric

Parameter NameAttribute value
Temperature identificationyes
Temperature identification typefusible ring
Connector typeShield terminator
Pre-installed leadsyes
Preassembled lead types55A0111
Lead splittingStranded wire
Lead plating materialstin
Lead colorwhite/black
Termination methodwelding
Insulating sleeve outer diameter2.65 mm [ .105 in ]
Expand inner diameter (minimum value)2.65 mm [ .105 in ]
Recovered inner diameter (maximum value).75 mm [ .03 in ]
total length16.5 mm [ .65 in ]
Preassembled lead size (mm²).15
Preassembled lead size (AWG)26
Shield outer diameter (minimum value)1.4 mm [ .055 in ]
Dielectric outer diameter (maximum).75 mm [ .03 in ]
Preassembled Lead Dimensions (CMA)304
Operating temperature (max) (°C)150
Resistance propertiesImmersion protection
Wire temperature (max) (°C)125
MIL/NAS specifications (MIL-S-83519, NAS-1747)no
Meet government qualificationsno
Installation Procedure for Standard SolderSleeve
Shield Terminators
Devices Installation Procedure
RCPS-100-70
Revision J1
5-Apr-18
RTS: 1376204
1.0
Scope:
This standard covers the installation procedure and inspection requirements for terminating cable
shields to ground leads using Tyco Electronics SolderSleeve shield terminators. The Tyco
Electronics part numbers covered by this document includes: S01, S02, S03, SO63, SO96, SO175,
ST18, ST63, D-108, and B-023.
References:
2.1
Tyco Electronics Instructions:
1. Operating instructions for the heating device used.
Application Equipment:
Tyco Electronics approved heat sources must be used to install these devices. The heater must be
equipped with the recommended reflector to concentrate the heat and protect surrounding materials
from damage.
Termination Procedure:
Unless otherwise noted on the Specification Control Drawing for the shield terminator being used,
the following procedures shall be used for all SolderSleeve shield termination devices.
WARNING
Follow installation instructions carefully. Use adequate ventilation and
avoid charring or burning during installation. Charring or burning the
product will produce fumes that may cause eye, skin, nose and throat
irritation. Consult Material Safety Data Sheets
RAY5103
or
RAY5104
for further information.
2.0
3.0
4.0
4.1
Ground Lead Preparation: (if using loose ground leads).
1. Remove 1/4 to 5/16 inch of the insulation from the end of the ground lead as shown.
Unless otherwise specified dimensions are in millimeters. [Inches dimensions are in between brackets]
© 2016-2018 TE Connectivity Corporation. All Rights Reserved. TE Proprietary & Confidential Information.
If this document is printed, it becomes uncontrolled. Check for latest revision.
Page 1 of 10
A simple question about computer composition! Thanks for your explanation!
1. Write a procedure called is-little-endian that returns 1 when compiled and run on a little-endian machine and 0 when compiled and run on a big-endian machine. This program should run on any machine...
lmx5078 Embedded System
[Video] In-depth understanding: Soc FPGA system performance
Introduction: How do CPU and FPGA share data in SoC FPGA? Is there a fast, low-latency, and consistent way to share data between hardware accelerators? For this kind of problem, ARM-based SoC devices ...
chenzhufly FPGA/CPLD
After modifying the ce5 audio driver cache, the system is not normal.
After adding the audio driver cache of 2440 ce5, the sound output of the touch screen click is abnormal. When the system load is light, it outputs two very light clicks, but when the load is heavy, th...
zmz.558 Embedded System
I'm writing a program similar to an e-book (browsing TXT files), but I've run into some problems.
I am writing a program similar to an e-book (browsing TXT files), but I encountered a problem when turning pages. Is it better to turn pages by a fixed number of words or by the number of lines? The l...
06benn Embedded System
Group purchase STM8S-Discovery development board (7 USD, absolutely great value) with touch key + emulator
建议大家团购STM8S-Discovery开发板(绝对超值) Learn, evaluate and use the STM8 microcontroller with the STM8S-Discovery kitThe STM8S-Discovery kit is the quickest way to explore and demonstrate STM8S105C6T6 function...
leang521 stm32/stm8
Experts, please help!
I've been using Wanli's medwin to simulate LCD online. I'm using C. The program compiles and links fine. When I download it to the simulator, the target system doesn't respond. I used the simplest sys...
unstaffic MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1972  2220  954  1075  623  40  45  20  22  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号