Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 1.0 (06-14-06)
DATASHEET
2
SMSC EMC1201/EMC1202
Single/Dual Single-Wire Temp Sensor in SOT23-5 Using SMSC BudgetBus
TM
Sensor Interface
Datasheet
Chapter 1 Pin Configuration
VDD
GND
BBUS
1
2
3
5
GND/DN
4
GND/DP
Figure 1.1 EMC1201 and EMC1202 Pin Configuration
1.1
Pin Description
Table 1.1 EMC1201 and EMC1202 Pin Description
PIN
VDD
GND
BBUS
GND/DP
GND/DN
PIN NO.
1
2
3
4
5
Supply Voltage V
DD
Ground
Serial Bus Interface to SMSC Host
Ground, or Diode 1 Positive Terminal, EMC1202 only
Ground, or Diode 1 Negative Terminal, EMC1202 only
DESCRIPTION
SMSC EMC1201/EMC1202
DATASHEET
3
Revision 1.0 (06-14-06)
Single/Dual Single-Wire Temp Sensor in SOT23-5 Using SMSC BudgetBus
TM
Sensor Interface
Datasheet
1.2
Absolute Maximum Ratings
Table 1.2 EMC1201/EMC1202 Maximum Ratings
DESCRIPTION
RATING
-0.3 to 5.0
-0.3 to V
DD
+0.3
0 to 85
-55 to 150
Refer to JEDEC
Spec. J-STD-020
UNIT
V
V
°C
°C
Supply Voltage V
DD
Voltage on any other pin
Operating Temperature Range
Storage Temperature Range
Lead Temperature Range
Package Thermal Characteristics for SOT23-5
Power Dissipation
Thermal Resistance(at 0 air flow)
ESD Rating, All Pins Human Body Model
TBD
131.7
2000
°C/W
V
Note:
Stresses above those listed could cause damage to the device. This is a stress rating only
and functional operation of the device at any other condition above those indicated in the
operation sections of this specification is not implied. When powering this device from
laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be
exceeded or device failure can result. Some power supplies exhibit voltage spikes on their
outputs when the AC power is switched on or off. In addition, voltage transients on the AC
power line may appear on the DC output. If this possibility exists, it is suggested that a clamp
circuit be used.
Revision 1.0 (06-14-06)
DATASHEET
4
SMSC EMC1201/EMC1202
Single/Dual Single-Wire Temp Sensor in SOT23-5 Using SMSC BudgetBus
I want to use a single chip microcomputer to complete the preset gate pulse generator in the picture, but I don’t know how to design it? Please give me some suggestions if you know, thank you....
I just used this board, and I'm a complete novice. I want to send a string of data to the arm through the serial port, and after some simple calculations, send the result to the pc. The multiple data ...
I am now using the Zigbee serial port to transparently read the data of an electrical parameter acquisition module. The communication port of the electrical parameter acquisition module is 485, and th...
Protothread is similar to the programming method of coroutine. All tasks only need one stack. Running in idle tasks and cooperating with raw os, the real-time performance is guaranteed. The famous IoT...
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
