CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3.
θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 4, 6),
Unless Otherwise Specified
TEST CONDITIONS
TEMP
(°C)
MIN
(NOTE 5)
TYP
MAX
(NOTE 5)
UNITS
PARAMETER
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
ON Resistance, R
ON
Full
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+
See Figure 4
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= Voltage at
Max R
ON,
Note 8
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
Note 9
V+ = 3.3V, V
COM
= 0.3, 3V, V
NO
or V
NC
= 3V, 0.3V
25
Full
25
Full
25
Full
25
Full
V+ = 3.3V, V
COM
= 0.3V, 3V, or V
NO
or V
NC
= 0.3V, 3V
25
Full
0
-
-
-
-
-
-
-3
-60
-3
-80
-
0.17
-
0.005
-
0.008
-
-
-
-
-
V+
0.25
0.3
0.02
0.04
0.06
0.07
3
60
3
80
V
Ω
Ω
Ω
Ω
Ω
Ω
nA
nA
nA
nA
R
ON
Matching Between Channels,
∆R
ON
R
ON
Flatness, R
Flat(ON)
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
COM ON Leakage Current,
I
COM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 2.7V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω, C
L
= 35pF,
V
IN
= 0 to 2.7V, See Figure 1, Note 7
V+ = 2.7V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω, C
L
= 35pF,
V
IN
= 0 to 2.7V, See Figure 1, Note 7
C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, See Figure 2
R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1 V
RMS,
See
Figure 3
R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1 V
RMS,
See
Figure 5
25
Full
25
Full
25
25
25
25
-
-
-
-
-
-
-
-
15
-
15
-
-125
62
-94
182
25
30
25
30
-
-
-
-
ns
ns
ns
ns
pC
dB
dB
pF
Turn-OFF Time, t
OFF
Charge Injection, Q
OFF Isolation
Crosstalk (Channel-to-Channel)
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
3
FN6091.2
June 23, 2006
ISL43L120, ISL43L121, ISL43L122
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 4, 6),
Unless Otherwise Specified
(Continued)
TEST CONDITIONS
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
TEMP
(°C)
25
25
MIN
(NOTE 5)
-
-
TYP
182
290
MAX
(NOTE 5)
UNITS
-
-
pF
pF
PARAMETER
COM OFF Capacitance,
C
COM(OFF)
COM ON Capacitance, C
COM(ON)
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Positive Supply Current, I+
V+ = 1.65V to 3.6V, V
IN
= 0V or V+, all channels on or
off
Full
25
Full
1.65
-
-
-
-
-
3.6
30
750
V
nA
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Input Voltage High, V
INH
Input Current, I
INH
, I
INL
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Guaranteed but not tested.
8. R
ON
matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value.
9. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
V+ = 3.3V, V
IN
= 0V or V+ (Note 7)
Full
Full
Full
-
1.4
-0.5
-
-
-
0.5
-
0.5
V
V
µA
Electrical Specifications - 1.8V Supply
Test Conditions: V+ = +1.65V to +2.0V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 4, 6),
Unless Otherwise Specified
TEST CONDITIONS
TEMP
(°C)
MIN
(NOTE 5)
TYP
MAX
(NOTE 5)
UNITS
PARAMETER
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
ON Resistance, R
ON
Full
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+, See
Figure 4, Note 7
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= Voltage at
Max R
ON,
Note 8
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
Note 9
V+ = 2.0V, V
COM
= 0.3V, 1.8V, V
NO
or V
NC
= 1.8V, 0.3V
25
Full
25
Full
25
Full
25
Full
V+ = 2.0V, V
COM
= 0.3V, 1.8V, or V
NO
or V
NC
= 0.3V,
1.8V
25
Full
0
-
-
-
-
-
-
-3
-60
-3
-80
-
0.26
-
0.005
0.005
0.074
0.082
-
-
-
-
V+
0.35
0.4
-
-
-
-
3
60
3
80
V
Ω
Ω
Ω
Ω
Ω
Ω
nA
nA
nA
nA
R
ON
Matching Between Channels,
∆R
ON
R
ON
Flatness, R
FLAT(ON)
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
COM ON Leakage Current,
I
COM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50Ω, C
L
= 35pF,
V
IN
= 0 to 1.65V, See Figure 1, Note 7
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50Ω, C
L
= 35pF,
V
IN
= 0 to 1.65V, See Figure 1, Note 7
C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, See Figure 2
25
Full
25
Full
25
-
-
-
-
-
30
-
25
-
-80
40
45
35
40
-
ns
ns
ns
ns
pC
Turn-OFF Time, t
OFF
Charge Injection, Q
4
FN6091.2
June 23, 2006
ISL43L120, ISL43L121, ISL43L122
Electrical Specifications - 1.8V Supply
Test Conditions: V+ = +1.65V to +2.0V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 4, 6),
Unless Otherwise Specified
(Continued)
TEST CONDITIONS
R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1 V
RMS,
See
Figure 3 and Figure 5
TEMP
(°C)
25
25
25
25
25
MIN
(NOTE 5)
-
-
-
-
-
TYP
62
-94
182
182
290
MAX
(NOTE 5)
UNITS
-
-
-
-
-
dB
dB
pF
pF
pF
PARAMETER
OFF Isolation
Crosstalk (Channel-to-Channel)
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
COM OFF Capacitance,
C
COM(OFF)
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = 1.65V to 3.6V, V
IN
= 0V or V+, all channels on or
off
25
Full
-
-
-
-
30
750
nA
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Input Voltage High, V
INH
Input Current, I
INH
, I
INL
V+ = 2.0V, V
IN
= 0V or V+ (Note 7)
Full
Full
Full
-
1.0
-0.5
-
-
-
0.4
-
0.5
V
V
µA
Test Circuits and Waveforms
V+
LOGIC
INPUT
50%
0V
t
OFF
SWITCH
V
INPUT
NO
90%
SWITCH
OUTPUT
0V
t
ON
V
OUT
90%
LOGIC
INPUT
SWITCH
INPUT
NO or NC
COM
IN
GND
R
L
50Ω
C
L
35pF
V
OUT
t
r
< 5ns
t
f
< 5ns
V+
C
Logic input waveform is inverted for switches that have the opposite
[i=s] This post was last edited by paulhyde on 2014-9-15 09:14 [/i] Will the audio question this year include mic and amplifier? Find a document on how to select bias resistors for a mic...
[align=center][font=punctuation]It can be said that the current development of sensors is in a state of full blossoming in many fields. Its subdivided products are so numerous and complex that it is n...
I am using mini2440, Nand Flash model is K9F1G08, and I am learning on bare metal. When I read, the first byte is always 30, followed by the real data. I cannot write. Please give me some advice. Than...
The delay in the lm3s811 routine is written like thisvoidDelay(unsigned long ulSeconds){//// Loop while there are more seconds to wait.//while(ulSeconds--){//// Wait until the SysTick value is less th...
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
1 Battery technology determines the fate of energy vehicles
Regardless of whether new energy vehicles are hybrid or pure electric vehicles, they cannot do without the core technology of batter...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
