EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

ACT24JB35AA [V001]

Description
JAM NUT RECEPTACLE
CategoryThe connector   
File Size856KB,17 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

ACT24JB35AA [V001] Overview

JAM NUT RECEPTACLE

ACT24JB35AA [V001] Parametric

Parameter NameAttribute value
Component typeelectrical connector
Connector Systemline to panel, line to panel
Sealableyes
Connectors and terminals terminate toWires and cables
Housing size11
shieldyes
Connector typefemale end, female end
Housing typeLock nut female end
Number of Positions13
Number of power supply locations0
Number of signal positions13
Pre-installedno
position keyingA
keyingKeyway polarization A
Factory installed rear caseno
Operating voltage (VAC)400
Voltage (Vrms)1300
Operating voltage (VDC)550
Penetration typeno
Entrance methodBack penetration
Shell plating materialCadmium, outer diameter
Shell materialcomposite
Insulation MaterialsHard dielectric/silica gel
Sealedno
Fluid typeM2-V, MIL-DTL-5624 (JP-4,JP-5), MIL-DTL-83133 (JP-8), MIL-PRF-23699, MIL-PRF-5606, MIL-PRF-7808, SEA
Environmental protection typeElastomeric seal
O-ring materialSilica gel
weight11.8 g [ .026 lb ]
environmental protectionyes
Perimeter sealing materialSilica gel
Contact Current Rating (Max) (A)5
reverse polarityno
Terminal layoutB35
Terminal typeLess Pin
Number of terminals (size 22D)13
Panel Mount Feature TypeLocknut
Panel mount featureswith
Connector mounting typePanel
polar codeA
Joint alignment typekeying
joint fixationwith
flangeLock nut flange
Joint fixation typeThree-head thread
Location monitoringTiming
Component length33 mm [ 1.3 in ]
Cable size.08 – .33 mm² [ 28 – 22 AWG ]
Acceptable wire insulation diameter range.76 – 1.37 mm [ .03 – .054 in ]
Panel thickness1.58 – 3.2 mm [ .062 – .126 in ]
Working group temperature range-65 – 200 °C [ -85 – 392 °F ]
fluid resistanceyes
Circuit ApplicationSignal
Durability Level (Cycles)500
Package quantity1
Ignored load locationall
How to achieve more accurate uS or mS level delay when writing the underlying driver of wince?
For example, I want a GPIO to be set to a high level first, and then become a low level after 2uS....
yezhenyu Embedded System
Asking for help from the forum about setting DDS on FPGA
: Let's start with the program: module DDS1(CLK1,DAC1,enable); input CLK1 ; input enable ; output[9:0] DAC1; reg [31:0] B1; parameter N=32'hfffff ; parameter M=32'h0 ; always @(negedge enable) begin i...
523335234 FPGA/CPLD
Protel wiring design considerations
Protel wiring design...
lorant PCB Design
EEWORLD University Hall----New Raspberry Pi 4: Can it replace your PC?
The new Raspberry Pi 4: Can it replace your PC ? : https://training.eeworld.com.cn/course/5324The new Raspberry Pi 4: Can it replace your PC?...
抛砖引玉 DIY/Open Source Hardware
SHT31 Review + Preliminary Understanding of Evaluation Board
After receiving the evaluation board, the first thing I did was to read the user manual. My English foundation is poor, so I can only learn with the help of Baidu Translate. The following is the user ...
hujj Special Edition for Assessment Centres
Newbie asks about adoce30.h
I just got started with EVC and want to use EVC4.0 to access ACCESS. I downloaded several examples from the Internet and debugged them, but they all had the same error: Cannot open include file: 'adoc...
qqnayz Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1935  628  1670  1772  973  39  13  34  36  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号