EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AG-02-1060-DJ

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 106ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AG-02-1060-DJ Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 106ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 0303,

WBC-T0303AG-02-1060-DJ Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802603446
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance106 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Under WM6.0, can the RIL driver use the IS637 structure to read and write SIM card text messages?
I am currently debugging a cdma modem to make a RIL driver for mobile6.0. I plan to use the CDMA feature. For the SMS part, I decided to use msgIS637InDeliver (receive) and msgIS637OutSubmit (send) to...
malebanshee Embedded System
XILINX FPGA design document for DDR SDRAM
This application note describes a 200 MHz DDR SDRAM (JEDEC DDR400 (PC3200) standard) controller implemented in Virtex-5 devices. This design implementation uses the IDELAY cell to adjust the read data...
eeleader FPGA/CPLD
To access a larger memory, use 51~~
What is the most convenient way to do it? The main problem is that there are not enough address lines. I want to connect 74LS273, but I don't know how to pull out the clock line... Or is there any oth...
冰人 51mcu
TI battery protection and fuel gauge solutions explained
Detailed explanation of TI battery protection and fuel gauge solutions, battery pack solutions for laptops, other industrial battery packs (1 to 9 cells), suitable for EPOS, Bluetooth speakers, and su...
qwqwqw2088 Analogue and Mixed Signal
433M Antenna
Has anyone used fiberglass for 433M antennas? Which one is better?...
hinii23 RF/Wirelessly
Single chip digital multimeter + program (already made into a physical object)
[i=s] This post was last edited by 158999437 on 2015-5-1 14:59 [/i] The board is also completed, hope to share with you! DC: 0~100V AC: 0~100V DC: 0~1a AC: 0~1a Resistance and current are made by 555 ...
158999437 Download Centre

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1430  2002  2558  2220  1424  29  41  52  45  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号