address inputs, A(12:0); and eight bidirectional data lines,
DQ(7:0). E1 and E2 are device enable inputs that control device
selection, active, and standby modes. Asserting both E1 and E2
enables the device, causes I
DD
to rise to its active value, and
decodes the 13 address inputs to select one of 8,192 words in
the memory. W controls read and write operations. During a
read cycle, G must be asserted to enable the outputs.
2
WRITE CYCLE
A combination of W less than V
IL
(max), E1 less than V
IL
(max),
and E2 greater than V
IH
(min) defines a write cycle. The state of
G is a “don’t care” for a write cycle. The outputs are placed in
the high-impedance state when either G is greater than
V
IH
(min), or when W is less than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access shown in
figure 4a, is defined by a write terminated byW going high, with
E1 and E2 still active. The write pulse width is defined by t
WLWH
when the write is initiated by W, and by t
ETWH
when the write
is initiated by the latter of E1 or E2. Unless the outputs have
been previously placed in the high-impedance state by G, the
user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access shown in
figure 4b, is defined by a write terminated by the latter of E1 or
E2 going inactive. The write pulse width is defined by t
WLEF
when the write is initiated by W, and by t
ETEF
when the write
is initiated by the latter of E1 or E2 going active. For the W
initiated write, unless the outputs have been previously placed
in the high-impedance state by G, the user must wait t
WLQZ
before applying data to the eight bidirectional pins DQ(7:0) to
avoid bus contention.
Total Dose
Table 2. Radiation Hardness
Design Specifications
1
1.0E6
1.0E9
1.0E12
1.0E-10
3.0E14
rads(Si)
rads(Si)/s 20ns pulse
rads(Si)/s 20ns pulse
errors/bit day
2
n/cm
2
Dose Rate Upset
Dose Rate Survival
Single-Event Upset
Neutron Fluencs
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% Adam’s worst case spectrum (-55
o
C to 125+
o
C).
Table 3. SEU versus Temperature
10
-4
10
-6
SEU
errors/bit-day
10
-8
10
-10
10
-12
10
-13
10
-14
10
-16
10
-13
10
-11
10
-10
RADIATION HARDNESS
The UT67164 SRAM incorporates special design and layout
features which allow operation in high-level radiation
environments.
-55
-35
-15
5
25
45
65
85
105 125
Temperature (
o
C)
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
LU
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
Thermal resistance, junction-to-case
2
Latchup immunity
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to V
DD
+ 0.5
-65 to +150°C
1.0W
+150°C
10°C/W
+/-150mA
+/-
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5V
-55 to +125°C
0V to V
DD
UNITS
V
o
C
V
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 5.0V±10%; -55°C <Tc < +125°C)
SYMBOL
V
IH
V
IL
V
OL
V
OH
C
IN 1
C
IO 1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
I
OL
= +/- 4.0mA, V
DD
= 4.5V
I
OH
= +/-4mA, V
DD
= 4.5V
ƒ
= 1MHz @ 0V, V
DD
= 4.5V
ƒ
= 1MHz @ 0V, V
DD
= 4.5V
V
IN
= V
DD
and V
SS
V
O
= V
DD
and V
SS
V
DD
= 5.5V
G = 5.5V
I
OS 2, 3
Short-circuit output current
V
DD
= 5.5V, V
O
= V
DD
V
DD
= 5.5V, V
O
= 0V
I
DD
(OP)
I
DD
(SB)
pre-rad
I
DD
(SB)
post-rad
Supply current operating @1MHz
CMOS inputs (I
OUT
= 0)
V
DD
= 5.5V
Supply current standby
CMOS inputs (I
OUT
= 0)
E1 = V
DD
- 0.5, V
DD
= 5.5V
CMOS inputs (I
OUT
= 0)
CS1 = negated V
DD
= 5.5V
CS2 = negated
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1.0E6 rads(Si).
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
There are few examples of using BLE to implement HID Touch Screen on the Internet. I tried it today. It can be connected under IOS, but it cannot be operated. There will be a mouse icon under ANDROID,...
According to the official Mbed blog , the classic Mbed online compiler will be retired and replaced by Keil Studio Cloud.Introducing Keil Studio Cloud and retiring Mbed Online CompilerLast updated on ...
Are you struggling at work right now and have no idea what to do next? If you are so bored with your job that you feel sleepy when you think about going to work, please raise your hand! You are not al...
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
The mass production process of the new generation of cockpit platform has started, and the smart cockpit market has entered a new bonus cycle of technology iteration and platform upgrade.
...[Details]
Today's security industry has entered the era of massive networking. Many enterprises, especially financial institutions, have established multi-level video surveillance networking platforms. Lever...[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
The automotive industry in 2025 is undergoing a thorough intelligent reshuffle.
Geely wants to make changes in the field of AI cockpits: in the future, there will be no traditional smart...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Office (USPTO) for a patent for a door anti-collision system that may be used in future Ford vehicl...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
