531VA28M0000BGR datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 531VA28M0000BGR

531VA28M0000BGR: DescriptionCMOS Output Clock Oscillator, 28MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size268KB，15 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

531VA28M0000BGR Overview

CMOS Output Clock Oscillator, 28MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

531VA28M0000BGR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
Reach Compliance Code	unknown
Other features	TAPE AND REEL
Frequency Adjustment - Mechanical	NO
frequency stability	50%
JESD-609 code	e4
Manufacturer's serial number	531
Installation features	SURFACE MOUNT
Nominal operating frequency	28 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS
physical size	7.0mm x 5.0mm x 1.85mm
Maximum supply voltage	1.89 V
Minimum supply voltage	1.71 V
Nominal supply voltage	1.8 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)
Base Number Matches	1

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.0 7/06

Si530/531

Recommended Resources

High input impedance buffer amplifier

Refrigerator undervoltage, overvoltage and power outage protector

Periodic timer using astable flip-flop

Photodiode isolation amplifier circuit

555 three-digit display capacitance meter circuit

Photosensitive signal amplification circuit

WinCE starts slowly: It will take a long time after Log2Phys: Logical 0x500 -> Physical 0x900 to reach System ready!...; Alan1987 Embedded System

[FPGA Tips] How fast is three-level logic? How to calculate?: wHow fast is 3- level logic? wThe wiring delay can be roughly estimated to be equal to the logic delay—The latency of the slice below is Tilo , the latency from F, G through the LUT outputTCKO, clock-...; eeleader FPGA/CPLD

Verilog Syntax Summary: 1: Basic variables in Verilog are wire net type and register type. Wire net type variables are synthesized into wires, while registers may be synthesized into wires, latches, and flip-flops. 2: Mappin...; eeleader FPGA/CPLD

Is everyone busy lately?: No new opinions were expressed....; eeleader Talking about work

[TI's First Low Power Design Contest] FR5969 LaunchPad Resource List: [i=s]This post was last edited by luyongcdpj on 2014-10-18 07:06[/i] Add it to the project and you can check it anytime without having to cut it out to look at the schematic. I feel that this chip has...; luyongcdpj Microcontroller MCU

How to change the library file in the schematic diagram in orcad?: The first method: edit the library file directly in the schematic diagram, and then update it to the schematic diagram. The operation is as follows: The first step is to select the component you want ...; 凡亿教育 PCB Design

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components