530TC123M000DGR datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 530TC123M000DGR

530TC123M000DGR: DescriptionCMOS Output Clock Oscillator, 123MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

530TC123M000DGR Overview

CMOS Output Clock Oscillator, 123MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

530TC123M000DGR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
package instruction	ROHS COMPLIANT, SMD, 6 PIN
Reach Compliance Code	unknown
Other features	TAPE AND REEL
Frequency Adjustment - Mechanical	NO
frequency stability	7%
JESD-609 code	e4
Manufacturer's serial number	530
Installation features	SURFACE MOUNT
Nominal operating frequency	123 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS
physical size	7.0mm x 5.0mm x 1.85mm
Maximum supply voltage	2.75 V
Minimum supply voltage	2.25 V
Nominal supply voltage	2.5 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)
Base Number Matches	1

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

PLC light source robot hand bubble control circuit

Inductive electric test pen circuit three

Parallel resonant tank circuit

High-pass active filter circuit using LM110

Small power circuit

Darkroom touch control circuit

Design of medical model training system based on Lingyang SPCE061A voice chip: [b]0 Introduction[/b] The medical mannequin training system is designed to meet the needs of medical students. The development of modern medical simulation technology in my country is just in its infa...; dtcxn Medical Electronics

I use LM317 to make a 24V voltage regulator. Why does it work when I add a load?: [color=#222222][backcolor=rgb(238, 238, 238)][font=sans-serif]As soon as a load is added, the voltage will be pulled down. What is the reason? Please ask for advice. Thank you. This is the circuit dia...; justsuperone Analogue and Mixed Signal

[GD32L233C-START Review] Chapter 5 Dynamic Scanning to Directly Drive 4-Bit Clock Digital Tube: [i=s]This post was last edited by yang_alex on 2022-2-21 17:56[/i]There are two ways to connect a single-chip microcomputer to drive a multi-digit digital tube: common anode and common cathode. Here w...; yang_alex GD32 MCU

The campus network has been unable to access the forum, the domain name can be resolved and the server is not responding: ?????????????????????????...; huo_hu 51mcu

I don't know how to drive the piezoelectric ceramic piece better. I found a few pictures elsewhere. Can you help me?: I don't know how to drive the piezoelectric ceramic better. I found some pictures elsewhere to help me find out how to drive it better. The MCU is STM8L101....; zxcm stm32/stm8

Detailed explanation of MSP430 microcontroller low power control and system working mode: [i=s]This post was last edited by qwqwqw2088 on 2014-9-30 10:05[/i] The SCG1, SCG2, OscOff and CPUOff bits in the CPU status register SR are important low-power control bits. Whenever any interrupt is...; qwqwqw2088 Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components