514-91-121-15-061034 datasheet, PDF

Datasheet> All Categories > The connector> socket> 514-91-121-15-061034

514-91-121-15-061034: DescriptionIC Socket, PGA121, 121 Contact(s),; CategoryThe connector socket; File Size146KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com

Download Datasheet Parametric View All

514-91-121-15-061034 Overview

IC Socket, PGA121, 121 Contact(s),

514-91-121-15-061034 Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	Mill-Max
Reach Compliance Code	compliant
ECCN code	EAR99
Other features	PGA SOCKET
Contact to complete cooperation	GOLD (10) OVER NICKEL (100)
Contact completed and terminated	Tin/Lead (Sn/Pb)
Contact material	NOT SPECIFIED
Device slot type	IC SOCKET
Type of equipment used	PGA121
Shell material	POLYCYCLOHEXYDIMETHYLENE TEREPHTHALATE-POLYESTER
JESD-609 code	e0
Number of contacts	121
Base Number Matches	1

Preview

Download Datasheet

View All

SURFACE MOUNT PIN GRID ARRAYS

For Standard .100” Spacing

Male Pin Header & Female Socket

•

Series 599 SMT PGA headers and Series 514 SMT PGA sockets are

assembled with MM pin# 9976, and receptacle# 1434 respectively.

Each floats vertically within the insulator to compensate for uneven

solder paste on the PCB. Typical example illustrated.

1) “Floating” pin SMT Headers using

machined epoxy insulator.

2) Detail of “Floating” pins which

compensate for unevenly

screened solder paste.

3) PQFP device

4) Translator board

5) Existing motherboard

Series 599, 514

Ordering Information

HEADER TYPE 9976

FOR PGA MALE PIN HEADER

1. Locate footprint pattern from pages 107 to 111, the middle 8 digits of

the part number will be located under the pattern.

Series

Plating

Code

Window

5 9 9

1 0

No. of pins

Grid size

Pattern #

4 7 6

Determined from footprint pattern pages 107 to 111

SPECIFY PLATING CODE XX=

10µ” Au

Pin Plating

SMT RECEPTACLE

TYPE 1434

FOR PGA FEMALE SOCKET

1. Specify 2-digit plating code from chart at bottom of page.

2. Locate footprint pattern from pages 107 to 111, the middle 8 digits of

the part number will be located under the pattern.

Series

Plating

Code

Window

5 1 4

No. of pins

Grid size

Pattern #

30µ” Au

0 3 4

Determined from footprint pattern pages 107 to 111

SPECIFY PLATING CODE XX=

Sleeve (Pin)

Contact (Clip)

200µ” Sn/Pb 200µ” Sn/Pb

10µ” Au

w w w. m i l l - m a x . c o m

102

516-922-6000

Recommended Resources

2-to-10 counter circuit and its signal waveform

Single pulse signal generating circuit c

YXQ-WY21-000 horizontal circular high-pressure steam sterilizer circuit

Temperature control circuit connection circuit diagram c

CMOS multipoint timer

Pulse dialing seven-way infrared remote control circuit

Is it better to connect two LED lights in series or in parallel to make them have the same brightness?: Two different LEDs, the anode is connected to +5V, and the cathode is connected to the I/O port. If you want the brightness to be the same when they are lit, is it better to connect them in series or ...; dirty Analog electronics

Remote login router settings: How to effectively manage Huawei 3COM routing devices? The most common way is to use the telnet command. As mentioned above, if the IP address of a router interface is 192.168.1.1, then we can execute...; liudong2008lldd RF/Wirelessly

LM3S8962 Development Board Ethernet Development Notes: Use the LM3S8962 development board to learn Ethernet related development 8962 integrates mac and phy but it seems that there is no protocol stack. I still don't understand the lwip of the example prog...; eeleader Microcontroller MCU

Learn Linux in Action in One Week: [align=left][color=rgb(102, 102, 102)][font=Tahoma][size=12pt] [/size][/font][/color][color=rgb(102, 102, 102)][font=微软雅黑][size=15pt]Linux is an open source, free operating system. Its stability, secu...; EE大学堂 Training Edition

CreateThread error in the driver: In the driver initialization function, create a threadif ( (pAXP182->IST = CreateThread(NULL, 0, AXP182_IST, NULL, 0, NULL)) == NULL) { dwErr = GetLastError(); DEBUGMSG(ZONE_ERR,(TEXT("AXP182_Init ERR...; neil.wang Embedded System

GSM module can't send text messages, please help me.: I use AT commands to send commands to the module through the computer serial port, but it has not been successful. I don’t know why? The baud rate is 115200. I send the following commands: 1. Send: at...; f56007 Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components