Note: Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 1 year aging at 25°C. We do not
recommend hand soldering the devices
REVISION A 01/08/15
3
IDT XO HCMOS CRYSTAL OSCILLATOR
XUH DATASHEET
DC Characteristics
(V
DD
= 2.5 V
± 5%, T
A
= - 20°C to +70°C; -40° to +85°C) Below are guaranteed for listed standard frequencies.
Parameter
Power Supply Current
Output HIGH Voltage
Output LOW Voltage
Enable/Disable Input HIGH Voltage
(Output enabled)*
Enable/Disable Input LOW Voltage
(Output disabled)
Symbol
I
DD
V
OH
V
OL
V
IH
V
IL
C
L
= 10pF
C
L
= 10pF
Condition
Standard Frequencies
Min
90%V
DD
Typ
80
Max
Units
mA
V
10%V
DD
70%V
DD
30%V
DD
V
V
V
* A pullup resistor from pin 4 (VDD) to pin 1 (E/D) enables output when pin 1 is left open.
AC Characteristics
(V
DD
= 2.5 V
± 5%, T
A
= - 20°C to +70°C; -40° to +85°C) Below are guaranteed for listed standard frequencies.
Note: Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 1 year aging at 25°C. We do not
recommend hand soldering the devices
IDT XO HCMOS CRYSTAL OSCILLATOR
4
REVISION A 01/08/15
XUH DATASHEET
DC Characteristics
(V
DD
= 1.8 V
± 5%, T
A
= - 20°C to +70°C; -40° to +85°C) Below are guaranteed for listed standard frequencies.
Parameter
Power Supply Current
Output HIGH Voltage
Output LOW Voltage
Enable/Disable Input HIGH Voltage
(Output enabled)*
Enable/Disable Input LOW Voltage
(Output disabled)
Symbol
I
DD
V
OH
V
OL
V
IH
V
IL
C
L
= 10pF
C
L
= 10pF
Condition
Standard Frequencies
Min
90%V
DD
Typ
54
Max
Units
mA
V
10%V
DD
70%V
DD
30%V
DD
V
V
V
* A pullup resistor from pin 4 (VDD) to pin 1 (E/D) enables output when pin 1 is left open.
AC Characteristics
(V
DD
= 1.8 V
± 5%, T
A
= - 20°C to +70°C; -40° to +85°C) Below are guaranteed for listed standard frequencies.
Note: Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 1 year aging at 25°C. We do not
I use EVC4, and the function I need to implement in the wince program is: how can I transfer a file to a shared folder on the PC. Note: The wince and PC are connected via a USB cable....
[i=s]This post was last edited by paulhyde on 2014-9-15 09:38[/i] [b]Research and Design of Remote Circuit Experiment Data Acquisition System Based on USB2.0[/b] With the development of modern compute...
I have been debugging the SD card initialization process, but it has not been successful. The specific situation is as follows: the initialization frequency is set to 300KHz, and the initialization st...
CH375 is connected to 8051 through the parallel port to transmit data, and the data is passed to the NAND gate through the P1.0 port for infrared transmission. How should this be programmed? Please en...
Embedded System
京公网安备 11010802033920号
EEWORLD
