PIC16F506
PIC16F506 Rev. C0
Silicon Errata and Data Sheet Clarification
The Rev. C0 PIC16F506 devices that you have received
conform functionally to the current Device Data Sheet
(DS41268D), except for the anomalies described in this
document.
The silicon/specification issues discussed in the
following pages are for silicon revision C0. If questions
arise concerning the silicon revision received in a
particular factory shipment, please contact your local
Microchip sales office for assistance.
Silicon Errata Issues
None.
©
2009 Microchip Technology Inc.
DS80475B-page 1
PIC16F506
Data Sheet Clarifications
The following typographic corrections and clarifications
are to be noted for the latest version of the device data
sheet (DS41268D):
Note:
Corrections are shown in
bold.
Where
possible, the original bold text formatting
has been removed for clarity.
1. Module: Analog-to-Digital Converter
(ADC)
For the PIC16F506, the specifications listed in
Table 1 below supersede Table 13-3 in the device
data sheet (DS41268D). These changes do not
apply to the PIC12F510, which is also described on
data sheet DS41268D.
TABLE 1:
Param
No.
A03
A04
A06
A07
Sym.
E
IL
E
DL
E
OFF
E
GN
A/D CONVERTER CHARACTERISTICS
Characteristic
Integral Error
Differential Error
Offset Error
Gain Error
Min.
—
—
—
—
Typ†
—
—
—
—
Max.
±1.5
-1 < E
DL
≤
+1.7
±1.5
-0.7≤ E
GN
≤+2.2
Units
LSB
LSB
LSB
LSB
Conditions
V
DD
= 5.0V
V
DD
= 5.0V
V
DD
= 5.0V
V
DD
= 5.0V
† Data in “Typ” column is at 5.0V 25°C unless otherwise stated. The typical parameters are for design
guidance only and are not tested.
Work around
None.
DS80475B-page 2
©
2009 Microchip Technology Inc.
PIC16F506
2. Module: Analog-to-Digital Converter
(ADC)
The Reset value for the ADCON0 register is
updated for Resets other than Power-on Reset.
Changes to the table affected are listed in
Table 10-4 below and are identified in bold and
italic text.
TABLE 10-4:
Register
W
INDF
TMR0
PCL
STATUS
FSR
OSCCAL
PORTB
PORTC
CM1CON0
ADCON0
ADRES
CM2CON0
VRCON
OPTION
TRISB
TRISC
Legend:
Note 1:
2:
RESET CONDITIONS FOR REGISTERS – PIC16F506
Address
—
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
—
—
—
Power-on Reset
qqqq qqqu
(1)
xxxx xxxx
xxxx xxxx
1111 1111
0001 1xxx
100x xxxx
1111 111-
--xx xxxx
--xx xxxx
1111 1111
1111 1100
xxxx xxxx
1111 1111
0011 1111
1111 1111
--11 1111
--11 1111
MCLR Reset, WDT Time-out,
Wake-up On Pin Change, Wake-up on
Comparator Change
qqqq qqqu
(1)
uuuu uuuu
uuuu uuuu
1111 1111
10uq quuu
(2)
10uu uuuu
uuuu uuu-
--uu uuuu
--uu uuuu
uuuu uuuu
1111
1100
uuuu uuuu
uuuu uuuu
uuuu uuuu
1111 1111
--11 1111
--11 1111
u
= unchanged,
x
= unknown, – = unimplemented bit, read as ‘0’,
q
= value depends on condition.
Bits <7:1> of W register contain oscillator calibration values due to
MOVLW XX
instruction at top of memory.
See Table 10-5 for Reset value for specific conditions.
Work around
None.
©
2009 Microchip Technology Inc.
DS80475B-page 3
PIC16F506
3. Module: Electrical Characteristics
The min. and max. values in Table 13-1 for Internal
Voltage Reference (V
IVRF
) have been revised.
Changes to the table are listed below and
identified in bold and italic text.
TABLE 13-1:
Sym
V
OS
V
CM
C
MRR
T
RT
V
IVRF
*
Note 1:
COMPARATOR SPECIFICATIONS
Characteristics
Min
—
0
+55*
—
0.500
Typ
±3
—
—
150
0.6
Max
±10
V
DD
– 1.5
—
400*
0.700
Units
mV
V
dB
ns
V
Internal
Comments
(V
DD
- 1.5V)/2
Input Offset Voltage
Input Common Mode Voltage
Common Mode Rejection Ratio
Response Time
(1)
Internal Voltage Reference
These parameters are characterized but not tested.
Response time measured with one comparator input at (V
DD
– 1.5)/2, while the other input transitions
from V
SS
to V
DD
– 1.5V.
Work around
None.
4. Module: Electrical Characteristics
The typ. value at 5V V
DD
and the max. values at
2V and 5V V
DD
have been revised as shown in
Table 2 below.
TABLE 2:
ICMP
Standard Operating Conditions (unless otherwise specified)
Operating Temperature 40°C
≤
T
A
≤
+85°C or -40°C to 125°C
Characteristic
Comparator Current
(2)
Min
—
—
Typ
(1)
15
60
Max
26
76
Units
μA
μA
Conditions
V
DD
= 2.0V (per comparator)
V
DD
= 5.0V (per comparator)
DC Characteristics
Param
No.
D023
Sym
ICMP
Note 1:
Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2:
For standby current measurements, the conditions are the same as I
DD
, except that the device is in Sleep
mode. If a module current is listed, the current is for that specific module enabled and the device in Sleep.
Work around
None.
DS80475B-page 4
©
2009 Microchip Technology Inc.
PIC16F506
5. Module: Electrical Characteristics
The max. values at 2V and 5V V
DD
for LP
Oscillator I
DD
at 125°C have been revised as
shown in Table 3 below.
TABLE 3:
LP OSCILLATOR 125°C I
DD
Standard Operating Conditions (unless otherwise specified)
Operating Temperature -40°C
≤
T
A
≤
+125°C (extended)
Characteristics
Supply Current
(2,3)
Min.
—
—
Typ
(1)
11
38
Max.
24
110
Units
μA
μA
Conditions
F
OSC
= 32 kHz, V
DD
= 2.0V
F
OSC
= 32 kHz, V
DD
= 5.0V
DC Characteristics
Param
No.
D010
Note 1:
2:
Sym.
I
DD
3:
Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern and temperature also have an impact on
the current consumption.
The test conditions for all I
DD
measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
SS
, T0CKI = V
DD
,
MCLR = V
DD
; WDT disabled unless noted otherwise.
Work around
None.
6. Module: Comparator Voltage Reference
Table 13-2 in data sheet DS41268D should read
as follows:
TABLE 13-2:
Sym
CV
RES
COMPARATOR VOLTAGE REFERENCE (V
REF
) SPECIFICATIONS
Characteristics
Min
—
—
—
—
—
—
—
Typ
V
DD
/24*
V
DD
/32
—
—
2K*
—
Max
—
—
±1/2*
±1/2*
—
10*
Units
LSb
LSb
LSb
LSb
Ω
μs
Comments
Low Range (V
RR
=
1)
High Range (V
RR
=
0)
Low Range (V
RR
=
1)
High Range (V
RR
=
0)
Resolution
Absolute Accuracy
(2)
Unit Resistor Value (R)
Settling Time
(1)
*
Note 1:
2:
These parameters are characterized but not tested.
Settling time measured while V
RR
=
1
and VR<3:0> transitions from
0000
to
1111.
Do not use reference externally when V
DD
< 2.7V. Under this condition, reference should only be
used as a comparator input with all input common mode voltage range limitations observed.
Work around
None.
©
2009 Microchip Technology Inc.
DS80475B-page 5
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
