REVISIONS
LTR
A
DESCRIPTION
Add three vendors, 18324, 1FN41, and 66579. Add device types 04, 05,
06, and 07. Add margin test method C. Update vendor's PIN. Change
code indent. no. to 67268. Editorial changes throughout.
Add device type 08 with vendors CAGE 1FN41 and CAGE 66579.
Added time temperature regression equation for unbiased bake.
Removed vendor CAGE 66302. Made technical changes to table I, 4.2
back end margin test method step 3, 4.3.1 step C, table II, and table III.
Editorial changes throughout. Added vendor's PIN from XMB/883 to
either LM/883 for appropriate device types. Deleted the top CE
waveform on figure 6. This was incorrect for this device.
Added vendor CAGE 34335 to the drawing as a source of supply for
device types 01 through 07. Add vendor CAGE number 66579 to device
types 01 through 04, also add vendor CAGE number 01295 to devices
04XX and 05XX. Add test condition A to 4.2 and 4.3.2. Add margin test
method E for vendor CAGE number 34335. Change to vendor similar
PIN for vendor CAGE numbers 1FN41 and 66579. Change to figure 3,
margin test method C for vendor CAGE 01295 and change to
programming waveforms. Change to 4.5. Editorial changes throughout.
Add case outline Z for vendor CAGE number 1FN41.
Changes in accordance with NOR 5962-R130-92.
Add case outline U. Add device types 09 and 10. Remove vendor
27014 from drawing. Editorial changes throughout.
Changes in accordance with NOR 5962-R118-94.
Updated boilerplate. Added device types 11-21. Removed vendors
1FN41, 18324, 34335, and 61394 from drawing. Added vendor 65786 to
drawing. Removed margin test methods from drawing.
Boilerplate update, part of 5 year review. ksr
DATE (YR-MO-DA)
87-12-17
APPROVED
M. A. Frye
B
89-01-01
M. A. Frye
C
90-12-05
M. A. Frye
D
E
F
G
92-01-30
93-10-15
94-02-16
97-06-11
M. A. Frye
M. A. Frye
M. A. Frye
Raymond Monnin
H
06-07-17
Raymond Monnin
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
CURRENT CAGE CODE IS 67268
REV
SHEET
REV
SHEET
OF SHEETS
PMIC N/A
REV STATUS
H
15
H
16
REV
SHEET
PREPARED BY
H
1
H
2
H
3
H
4
H
5
H
6
H
7
H
8
H
9
H
10
H
11
H
12
H
13
H
14
James E. Jamison
CHECKED BY
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
Charles Reusing
APPROVED BY
http://www.dscc.dla.mil
Michael A. Frye
DRAWING APPROVAL DATE
87-02-12
REVISION LEVEL
H
MICROCIRCUIT, MEMORY,
DIGITAL, CMOS, 262,144-BIT
(32K x 8) UV ERASABLE PROM,
MONOLITHIC SILICON
SIZE
CAGE CODE
A
SHEET
14933
1 OF
16
5962-86063
DSCC FORM 2233
APR 97
5962-E528-06
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)
and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
For device class M:
5962
│
│
│
Federal
stock class
designator
\
-
│
│
│
RHA
designator
(see 1.2.1)
\/
Drawing number
86063
01
│
│
│
Device
type
(see 1.2.2)
X
│
│
│
Case
outline
(see 1.2.4)
X
│
│
│
Lead
finish
(see 1.2.5)
/
For device classes Q and V:
5962
│
│
│
Federal
stock class
designator
\
-
│
│
│
RHA
designator
(see 1.2.1)
\/
Drawing number
86063
01
│
│
│
Device
type
(see 1.2.2)
Q
│
│
│
Device
class
designator
(see 1.2.3)
X
│
│
│
Case
outline
(see 1.2.4)
X
│
│
│
Lead
finish
(see 1.2.5)
/
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01,11
02,12
03,13
04,14
05,15
06,16
07,17
08,18
09,19
10,20
21
Generic number
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
(see 6.6)
Circuit
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
32K x 8-bit UV EPROM
Access time
200 ns
250 ns
300 ns
170 ns
150 ns
120 ns
90 ns
70 ns
55 ns
45 ns
35 ns
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level
as follows:
Device class
M
Q or V
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86063
SHEET
H
2
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Y
Z
U
Descriptive designator
GDIP1-T28 or CDIP2-T28
CQCC1-N32
See figure 1
CDIP3-T28 or GDIP4-T28
Terminals
28
32
32
28
Package style 1/
Dual-in-line
Rectangular leadless chip carrier
J-lead chip carrier
Dual-in-line
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings.
Storage temperature -------------------------------------------
Input voltages with respect to ground ------------------------
Output voltages with respect to ground ---------------------
VPP supply voltage with respect to ground -----------------
Power dissipation (PD) 2/ ---------------------------------------
Lead temperature (soldering, 10 seconds)------------------
Thermal resistance, junction-to-case (ΘJC):
Case outlines X, Y, and U -------------------------------
Case outline Z ----------------------------------------------
Junction temperature (TJ) --------------------------------------
1.4 Recommended operating conditions.
Case operating temperature (TC) ----------------------------
Supply voltage (VCC)---------------------------------------------
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
-55°C to +125°C
+4.5 V dc to +5.5 V dc
-65°C to +150°C
+6.5 V dc to -0.3 V dc
VCC +0.3 V dc to GND -0.3 V dc
+14.0 V dc to -0.6 V dc
+500 mW
+300°C
See MIL-STD-1835
13°C/W
+150°C
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or
http://assist.daps.dla.mil
or from
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless
a specific exemption has been obtained.
1/ Lid shall be transparent to permit ultraviolet light erasure.
2/ Must withstand the added PD due to short circuit test; e.g., IOS.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86063
SHEET
H
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table shall be as specified on figure 3.
3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices shall be as specified on figure 3. When required
in screening (see 4.2 herein) or qualification conformance inspection, groups A, B, or C (see 4.4), the devices shall be
programmed by the manufacturer prior to test. A minimum of 50 percent of the total number of cells shall be programmed.
3.2.3.2 Programmed devices. The requirements for supplying programmed devices are not a part of this drawing.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Processing EPROMS. All testing requirements and quality assurance provisions herein shall be satisfied by the
manufacturer prior to delivery.
3.6.1 Erasure of EPROMS. When specified, devices shall be erased in accordance with the procedures and characteristics
specified in 4.5.
3.6.2 Programmability of EPROMS. When specified, devices shall be programmed to the specified pattern using the
procedures and characteristics specified in 4.6.
3.6.3 Verification of state of EPROMS. When specified, devices shall be verified as either programmed to the specified
pattern or erased. As a minimum, verification shall consist of performing a functional test (subgroup 7) to verify that all bits are in
the proper state. Any bit that does not verify to be in the proper state shall constitute a device failure and shall be removed from
the lot.
3.7 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86063
SHEET
H
4
TABLE I. Electrical performance characteristics.
Test
│
│Symbol
│
│
│
│I
LI
│
│
│I
LO 1/
│
│
│I
CC1
│
│
│
│
│
│
│
│I
CC2
│
│
│
│
│
│
│
│
│I
SB1
│
│
│
│
│
│I
SB2
│
│
│
│
│I
PP
│
│
│V
IL1
│
4/
│
│
│V
IL2
│
4/
│
│
│V
IH1
│
4/
│
│
│
│V
IH2
│
4/
│
│
│
Conditions
│
-55°C < TC < +125°C
│
4.5 V dc < VCC < 5.5 V dc
│
unless otherwise specified
│
│V
IN = 0 to 5.5 V
│
│
│V
OUT = 0 to 5.5 V
│
│
2/ 3/
│CE
= OE = VIL
│V
PP = VCC
│0
0-7 = 0 mA
│
1
│f
= tACC maximum
│
│
│
│
│
│
│
│
│
│
│
│
│CE
= VIH
│V
CC = 5.5 V, f = 0 MHz
│
│
│
│
│
│
│
│
│
│V
PP = VCC = 5.5 V
│
│
│V
PP = VCC
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
Limits
│Device │
Group A
│
│
│
type
│subgroups │
Min
│
Max
│
│
│
│
│
│
│
│
│
All
│
1, 2, 3
│
│+10
│
│
│
│
│
│
│
│
│
All
│
1, 2, 3
│
│+10
│
│
│
│
│11-20 │
│
│
60
│01-05 │
1, 2, 3
│
│
50
│
06
│
│
│
65
│
│
│
70
│
07
│
08
│
│
│
90
│
09
│
│
│
115
│
10
│
│
│
130
│
21
│
│
│
85
│
│
│
│
│01,02, │
1, 2, 3
│
│
25
│
03
│
│
│
│04,05 │
│
│
40
│
06
│
│
│
55
│07,11-20│
│
│
60
│08,09 │
│
│
90
│
10
│
│
│
100
│
21
│
│
│
85
│
│
│
│
│01-05 │
1, 2, 3
│
│
3
│06,07, │
│
│
5
│08,09, │
│
│
│
│
│
45
│
10
│11-21 │
│
│
25
│
│
│
│
│01-07, │
1, 2, 3
│
│
300
│08,09, │
│
│
│
10
│
│
│
45
│11-21 │
│
│
25
│
│
│
│
│01-10 │
1, 2, 3
│
│
200
│11-21 │
│
│
10
│
│
│
│
│
All
│
1, 2, 3
│
-0.1
│
0.8
│
│
│
5/
│
│
│
│
│
│
│
│
│
│
All
│
1, 2, 3
│
-0.2
│
0.2
│
│
│
5/
│
│
│
│
│
│
│
│
│
│
All
│
1, 2, 3
│
2.0
│
VCC
│
│
│
│
+1.0
│
│
│
│
5/
│
│
│
│
│
│
│
│
│
All
│
1, 2, 3
│
VCC
│
VCC
│
│
│
-0.2
│
+0.2
│
│
│
│
5/
│
│
│
│
│
│
Unit
│
│
│
│
µA
│
│
│
µA
│
│
│
mA
│
│
│
│
│
│
│
│
mA
│
│
│
│
│
│
│
│
│
mA
│
│
│
│
│
│
µA
│
│
mA
│
│
│
µA
│
│
│
V
│
│
│
│
V
│
│
│
│
V
│
│
│
│
│
V
│
│
│
Input load current
Output leakage
current
Operating current
TTL inputs
Operating current
CMOS inputs
Standby current
TTL inputs
Standby current
CMOS inputs
VPP read current
Input low voltage
(TTL) (±10
percent supply)
Input low voltage
(CMOS)
Input high voltage
(TTL) (±10
percent supply)
Input high
voltage (CMOS)
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86063
SHEET
H
5
京公网安备 11010802033920号
EEWORLD
