Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +5.0V ±5%, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage
Input Voltage High
Input Voltage Low
Input Leakage Current
Active Current
Output Current High
Output Current Low
Input Capacitance
SYMBOL
V
CC
V
IH
V
IL
I
L
I
CC
I
OH
I
OL
C
IN
(Note 2)
(Note 2)
(Note 2)
0V
≤
V
IN
≤
V
CC
V
CC
= 5.25V, period = minimum (Notes 3, 4)
V
CC
= 4.75V, V
OH
= 4.0V
V
CC
= 4.75V, V
OL
= 0.5V
T
A
= +25°C (Note 5)
12
5
10
-1
17
CONDITIONS
MIN
4.75
2.2
0.8
1
70
-1
TYP
5.00
MAX
5.25
UNITS
V
V
V
µA
mA
mA
mA
pF
TIMING CHARACTERISTICS
(V
CC
= +5.0V ±5%, T
A
= +25°C, unless otherwise noted.)
PARAMETER
Input Pulse Width
Input-to-Tap Delay
(leading edge)
Input-to-Tap Delay
(trailing edge)
Power-Up Time
Period
Note 1:
Note 2:
Note 3:
Note 4:
SYMBOL
t
WI
t
PLH
t
PHL
t
PU
(Note 6)
4(t
WI
)
CONDITIONS
(Note 6)
(Notes 7–10)
(Notes 7–10)
MIN
40% of TAP5
t
PLH
See
Part Number and
Delay Times
table
See
Part Number and
Delay Times
table
100
TYP
MAX
UNITS
ns
ns
ns
ms
ns
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10:
Specifications to -40°C are guaranteed by design, not production tested.
All voltages referenced to GND.
Measured with outputs open.
I
CC
is a function of frequency and TAP5 delay. Only an MXD1005_ _60 operating with a 40ns period and V
CC
= +5.25V will
have a maximum I
CC
of 70mA. For example, an MXD1005_ _100 will not exceed 30mA. See Supply Current vs. Input
Frequency graph in
Typical Operating Characteristics.
Guaranteed by design.
Pulse width and/or period specifications may be exceeded, but accuracy is application sensitive (i.e., layout, decoupling, etc.).
V
CC
= +5V at +25°C. Typical delays are accurate on both rising and falling edges within ±2ns or ±3%.
See
Test Conditions
section.
The combination of temperature variations from +25°C to 0°C or +25°C to +70°C and voltage variation from 5.0V to 4.75V
or 5.0V to 5.25V may produce an additional typical input-to-tap delay shift of ±1.5ns or ±4%, whichever is greater.
All taps and outputs delays tend to vary unilaterally with temperature or supply variations. For example, if TAP1 slows
down, all other taps will also slow down; TAP3 cannot be faster than TAP2.
京公网安备 11010802033920号
EEWORLD
