805-007EPHBBMPN-72 datasheet, PDF

Datasheet> All Categories > The connector> 805-007EPHBBMPN-72

805-007EPHBBMPN-72: DescriptionInterconnection Device; CategoryThe connector; File Size445KB，8 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

805-007EPHBBMPN-72 Overview

Interconnection Device

805-007EPHBBMPN-72 Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	compliant
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed serial interconnects

mil spec performance. Glenair’s ASAP “Mighty Mouse”

cordsets are available for 100BASE-T, Gigabit Ethernet,

IEE 1394 and USB 2.0 applications.

These cordsets combine aerospace-grade data cables

with Series 80 “Mighty Mouse” harsh environment

connectors for maximum performance and minimum

size.

FEP jackets

meet FAA flammability requirements. Or,

choose

low smoke/ zero halogen polyurethane jackets

for mass transit or shipboard applications.

100BASE-T Cordset With 4 Pin Series 800

Connector

Three Strain Relief Options

– Overmolded, threaded

backshell or heatshrink boots.

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the six types of Series 80 connectors. For more information on selecting

a connector, please refer to the connector selection chart in the Introduction.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and tem pin connectors are used for 8 wire cocables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight a nd removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

J-1

E-Mail: sales@glenair.com

Recommended Resources

Design of universal card reader circuit based on NFC

CB3450 combined semi-automatic turret lathe electrical schematic circuit 02

Optical transmission detection circuit

Gain Programmable Isolation Amplifier 1

Simple electronic keyboard without power switch

Super regenerative receiving component CS902 (used in conjunction with transmitting component CS901)

Speaker? Piggy bank? ?: Is the little thing in the picture above a speaker or a piggy bank? If it is really that simple, wouldn't it be a waste of my typing so many words on the holiday? Without keeping you in suspense, I wi...; 小丸子 DIY/Open Source Hardware

gw1n FPGA reads ADS8598H actual DC measurement: The experimental board has not been fully soldered yet. Use flying wires to connect to the FPGA to measure its 3.3V power supply. The multimeter measures 3.293V.At present, the FPGA side directly chec...; littleshrimp Domestic Chip Exchange

Shouldn't the charging curve of a capacitor be inversely proportional to its discharging curve?: Shouldn't the charging curve of a capacitor be inversely proportional to its discharging curve?...; QWE4562009 Integrated technical exchanges

Various topics for e-sports competitions: [i=s]This post was last edited by paulhyde on 2014-9-15 09:10[/i] These are reports on various topics, very useful, make good use of them...; zhixiongxue Electronics Design Contest

Isolation problem of ground wire of DC linear regulated power supply?: I plan to make a 220V AC to ±12V, ±5V, 3.3V DC linear voltage regulator power supply. Do the ground wires of different voltages need to be isolated? I use a series of voltage regulator chips such as L...; 燕园技术宅 Power technology

IP core issues in ISE: Recently I downloaded a code about implementing UDP protocol with FPGA from CSDN. The board of the code is xc6slx45-2csg324, and my board model is xc3s500e-4pq208. When translating, an error message a...; Domipy FPGA/CPLD

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components