A50-43MP43F-10-P datasheet, PDF

Datasheet> All Categories > Radio frequency and microwave> A50-43MP43F-10-P

A50-43MP43F-10-P: DescriptionFixed Attenuator, 0MHz Min, 4000MHz Max,; CategoryRadio frequency and microwave; File Size653KB，5 Pages; ManufacturerSpinner GmbH

Download Datasheet Parametric View All

A50-43MP43F-10-P Overview

Fixed Attenuator, 0MHz Min, 4000MHz Max,

A50-43MP43F-10-P Parametric

Parameter Name	Attribute value
Maker	Spinner GmbH
Reach Compliance Code	unknown
Other features	4.3/10-F; 4.3/10-M
Nominal attenuation	10 dB
Characteristic impedance	50 Ω
structure	COAXIAL
Maximum input power (CW)	46.99 dBm
Maximum operating frequency	4000 MHz
Minimum operating frequency
Maximum operating temperature	40 °C
Minimum operating temperature	-40 °C
RF/Microwave Device Types	FIXED ATTENUATOR
Maximum voltage standing wave ratio	1.3
Base Number Matches	1

Preview

Download Datasheet

View All

DATA SHEET

Attenuator 25 to 200 W

Type 25

Type 50

Type 100

Type 200

Attenuators are optionally also available with integrated DC-Break which have to be specified via Sales Article Numbers

shown on last page. Frequency range and VSWR vary for these types and are shown in table below.

General technical data

Frequency range, Attenuator

VSWR, max., Attenuator

Frequency range, Attenuator +

integrated DC-break

VSWR, max., Attenuator +

integrated DC-break

1.06 @ DC to 1

GHz

DC to 4 GHz (Extra feature: to 6 GHz)

1.14 @ 1 to 2

GHz

1.20 @ 2 to 3

GHz

100 to 6000 MHz

1.70 @ 100 to

330 MHz

1.25 @ 330 to

694 MHz

1.20 @ 694 to

2690 MHz

1.30 @ 2690 to

3800 MHz

1.40 @ 5000 to

6000 MHz

1.30 @ 3 to 4

GHz

1.40 @ 4 to 6

GHz

Attenuation

DC to 4 GHz

4 to 6 GHz

3 ± 0.5 dB

3 ± 0.7 dB

6 ± 0.5 dB

6 ± 0.7 dB

10 ± 0.6 dB

10 ± 1.0 dB

20 ± 1.0 dB

20 ± 1.3 dB

30 ± 1.0 dB

30 ± 1.5 dB

40 ± 2.0 dB

40 ± 3.0 dB

Power

Power dissipation, max.

Type 25

25 W

Type 50

50 W

Type 100

100 W

Type 200

200 W

Input power, max

in both directions

@ 3 dB

50 W

100 W

150 W

300 W

@ 6 dB

30 W

65 W

120 W

200 W

@ 10 dB

25 W

50 W

100 W

200 W

@ 20 dB

25 W

50 W

100 W

200 W

@ 30 dB

25 W

50 W

100 W

200 W

@ 40 dB

25 W

50 W

100 W

200 W

Type 25

Type 50

Type 100

Type 200

Template TD-00003E

SPINNER GmbH │ www.spinner-group.com │ info@spinner-group.com

Data subject to change without notice │ Issue H

1/5

Recommended Resources

STK1040 power amplifier circuit diagram

Huanyu MWH-I multifunctional all-round alarm circuit trigger part circuit

Negative voltage slope fast charger circuit

NJU7662 application circuit diagram c

Using photoelectric isolation coupling to control AC load circuit

Computer motherboard circuit diagram 810 4_05

Dear heroes: What is the English name for baseboard and core board?: The company requires some information to be translated into English, but I don't know how to translate the two words "baseboard" and "core board". If anyone can provide a dictionary of relevant terms,...; zhaoboqian Embedded System

Based on FOC2.0, the torque of the three-phase sensor hub motor is small and unstable under low-speed control: I am currently debugging a three-phase sensored hub motor based on FOC2.0 control. Now the motor can run smoothly at a faster speed, but under low-speed control, the motor torque is small and unstable...; yangkai0008 Industrial Control Electronics

Received the board, the snail-like internet speed is unbearable: I received the board yesterday. I ran more than 10 miles to the courier to pick it up. Then I went to the Internet cafe to download the CD and information. I kept downloading until dark. The three lar...; 陈韶华 Embedded System

51 MCU C language complete tutorial: Very good information, I recommend it to everyone! [url=http://www.neoic.cn/bbs/read-htm-tid-204.html]51 MCU C Language Complete Tutorial[/url] [[i] This post was last edited by shuijian on 2008-10-21...; shuijian 51mcu

Automating Fiber Optic Calibration Using NI PXI, Motion, and Vision: Automating Fiber Optic Calibration Using NI PXI, Motion, and Vision...; lorant Analogue and Mixed Signal

6713 HPI problem help: My board is connected to 6713 and FPGA through HPI port. Now I want to transfer a frame of image from FPGA to SDRAM outside 6713. I read the HPI datasheet and wrote the program according to the steps ...; ip602 DSP and ARM Processors

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components