801-021FPHBBZ1PN-72 datasheet, PDF

Datasheet> All Categories > The connector> 801-021FPHBBZ1PN-72

801-021FPHBBZ1PN-72: DescriptionInterconnection Device; CategoryThe connector; File Size445KB，8 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

801-021FPHBBZ1PN-72 Overview

Interconnection Device

801-021FPHBBZ1PN-72 Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	compliant
Is Samacsys	N
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed serial interconnects

mil spec performance. Glenair’s ASAP “Mighty Mouse”

cordsets are available for 100BASE-T, Gigabit Ethernet,

IEE 1394 and USB 2.0 applications.

These cordsets combine aerospace-grade data cables

with Series 80 “Mighty Mouse” harsh environment

connectors for maximum performance and minimum

size.

FEP jackets

meet FAA flammability requirements. Or,

choose

low smoke/ zero halogen polyurethane jackets

for mass transit or shipboard applications.

100BASE-T Cordset With 4 Pin Series 800

Connector

Three Strain Relief Options

– Overmolded, threaded

backshell or heatshrink boots.

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the six types of Series 80 connectors. For more information on selecting

a connector, please refer to the connector selection chart in the Introduction.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and tem pin connectors are used for 8 wire cocables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight a nd removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

J-1

E-Mail: sales@glenair.com

Recommended Resources

Half-wave rectifier adjustable charging circuit

temperature controller circuit

Switching regulator circuit diagram with one additional switch tube

TDA2003 power amplifier circuit diagram

Application of integrated gas sensors in power transformer fault early warning devices

Flashing colored lights circuit diagram 2

Interrupt Marker: StartFragmentHow to transfer the value calculated in the stm32f10x_it.c interrupt function to the main.c file to use it , that is, mark the number of interrupts and then use it in main.c Use extern or...; duzhiming stm32/stm8

Code Help 1: process(clk) begin --if (rising_edge(clk)) then if count< 4999999 then count<=count+1 ; else outled<= not outled; count<=0; end if; --end if; end process; 50MHZ CLK Without if (rising_edge(clk)), the ...; 4027379 FPGA/CPLD

What interface is this???: [img]http://f:\aaaa[/img]...; woolsack Embedded System

Protel99SE Metal Slot Making: [p=35, null, left][backcolor=rgb(222, 240, 251)][color=rgb(74, 74, 74)][font=微软雅黑][size=14px]The correct way to draw a long groove in Protel 99 SE is to use the following figure to stack holes of Pad ...; PCBBCP PCB Design

2011 High-Tech Fair: How Chinese and Japanese manufacturers survive: Figure 1. Overview of Shenzhen High-Tech Fair Electronics Pavilion No. 2"If you are lucky, you only need one morality and not more, and it will be easier for you to cross the bridge." — Nietzsche“Japa...; 思潇 Discrete Device

stm8s self-upgrade problem help: When doing IAP self-upgrade, I found the following problem. I followed the instructions to operate the lkf file. I found the following error: mcu_app.lkf:1 no default placement for segment .const. The...; terry_cui stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components