EEWORLDEEWORLDEEWORLD

Part Number

Search

13445CDGX640ULU487

Description
Pushbutton Switch, DPDT, Momentary, 0.1A, 30VDC, Solder Terminal, Panel Mount-threaded
CategoryMechanical and electronic products    switch   
File Size258KB,8 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

13445CDGX640ULU487 Overview

Pushbutton Switch, DPDT, Momentary, 0.1A, 30VDC, Solder Terminal, Panel Mount-threaded

13445CDGX640ULU487 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompli
ECCN codeEAR99
Actuator typeSTANDARD TYPE
body width14 mm
body height12.7 mm
Maximum contact current (DC)0.1 A
Contact (DC) maximum rated R load.1A@30VDC
Maximum contact voltage (DC)30 V
Electrical life50000 Cycle(s)
Manufacturer's serial number13000
Installation featuresPANEL MOUNT-THREADED
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealDUST PROOF; WATER PROOF
surface mountNO
Switch actionMOMENTARY
switch functionDPDT
Switch typePUSHBUTTON SWITCH
Termination typeSOLDER
Base Number Matches1
13000 series
Professional quick-break momentary pushbutton switches
Distinctive features and specifications
PC and panel mount models
Bushing Ø 6,35 (1/4) and 11,9 (15/32)
UL and CECC approved
B
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load :
- silver contacts (A-AD2) : 2A 250VAC - 4A 125VAC - 4A 30VDC
- gold plated contacts (CD) : 100mA 30V
• Minimum load (AD2-CD contacts) : 10mA 50mV, 10µA 5V min.
• Initial contact resistance : 10 mΩ max.
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
2.000 Vrms 50 Hz min. between poles and between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life :
Contacts
A
AD2
CD
Max. current/voltage rating
2A 250VAC - 4A 125VAC - 4A 30VDC
2A 250VAC - 4A 125 VAC - 4A 30VDC
(gold plating : 100mA 30VDC max.)
100mA 30VDC
Low level or mechanical life
Number of cycles
50.000
20.000
50.000
150.000
MATERIALS
GENERAL SPECIFICATIONS
• Case : diallylphthalate (DAP)
• Actuator : brass, chrome plated
• Bushing : brass, nickel plated
• Housing : brass, nickel plated
• Contacts :
A
: silver
AD2
: silver, gold plated
(2 micron gold)
CD
: brass, gold plated
• Terminal seal : epoxy
Note : AD2 contacts can be used for high level applications.In this case, the
gold layer is considered only as a protection against oxidation during
storage.
• Torque : 1,25 Nm (.922 Ft.lb)
max. applied to nut
• Standard panel thickness : 2 mm
(.078 ) max.
• Total travel : 2 mm (.078)
• Operating temperature :
-40°C to +85°C
B-62
www.apem.com
APEM
Some doubts about the official routines of porting STM32 to uCOS
In the past two days, I downloaded the official routine (uCOSII-ST-STM32F103ZE-SK) ported from ucos to the STM32F103ZE-SK development board. There are two folders in it, uc-CPU and uc-LIB. I don't qui...
lsbeilei stm32/stm8
About STM32's TIM1 generates two pairs of PWM waves with dead zone complementary stacking
I want to generate two pairs of four tubes of PWM-controlled inverter full-bridge with complementary symmetry in dead zone, TIM1_CH1 (PA8) and TIM1_CH1N (PB13), TIM1_CH2 (PA9) and TIM1_CH2N (PB14). Sh...
506977544 stm32/stm8
How to change LCD screen from horizontal to vertical?
I'm using 2450. I want to know what else I need to modify in the driver besides the resolution in the header file to change the LCD screen from horizontal to vertical? I only changed the resolution de...
twpma Embedded System
IAR5.3 (Evaluation Version) always prompts the following error when compiling. What's going on?
Error[Lp021]: the destination for compressed initializer batch "P2 mid-1" is placed at an address that is dependent on the size of the batch, which is not allowed when using packbits compression. Cons...
zhaokuiyin Embedded System
Powering Smart Homes with the bq25606 Simple Charger
[i=s]This post was last edited by qwqwqw2088 on 2020-7-16 16:58[/i]Advances in wireless connectivity and low-power embedded processing have enabled new applications for smart homes and buildings. Most...
qwqwqw2088 Analogue and Mixed Signal
AD9852 has no output
When using DSP28335 to control AD9852, I found that there was no output, but the board was quite hot, which means it was working. Now I can't find the reason. Could you please tell me how to solve it?...
caijianfa55 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2123  1714  637  1305  2632  43  35  13  27  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号