EEWORLDEEWORLDEEWORLD

Part Number

Search

7046Y7CDBU612

Description
Rocker Switch, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Narrow Paddle Type Actuator, Through Hole-straight
Categoryswitch    Become warped plate switch   
File Size512KB,14 Pages
ManufacturerAPEM
Environmental Compliance  
Download Datasheet Parametric View All

7046Y7CDBU612 Overview

Rocker Switch, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Narrow Paddle Type Actuator, Through Hole-straight

7046Y7CDBU612 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Is SamacsysN
Actuator typeNARROW PADDLE TYPE
body width12 mm
body height19.6 mm
Body length or diameter19.05 mm
Contact (AC) maximum rated R load.02A@20VAC
Maximum contact current (AC)0.02 A
Maximum contact current (DC)0.02 A
Contact (DC) maximum rated R load.02A@20VDC
Maximum contact voltage (AC)20 V
Maximum contact voltage (DC)20 V
Electrical life50000 Cycle(s)
Manufacturer's serial number7000
Installation featuresTHROUGH HOLE-STRAIGHT
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED
switch functionDPDT
Switch typeROCKER SWITCH
Termination typeSOLDER
Base Number Matches1
7000 series
Rocker and paddle switches
Distinctive features and specifications
Wide variety of actuators
Many mounting styles for panel or PCB
VDE, UL and CSA approved
ELECTRICAL SPECIFICATIONS
• Current/voltage rating with resistive load :
Contact
Silver A
Silver,
gold plated AD
Brass,
gold plated CD
Maximum
3A 250VAC - 6A 125VAC - 4A 30VDC
3A 250VAC - 6A 125 VAC - 4A 30VDC
Gold plating withstands up to 100mA 30VDC.
0,4 VA at 20VAC or DC
Minimum
50mA 10VDC
10mA 50mV
10µA 5V
10mA 50mV
10µA 5V
Level *
III and IV
I to IV
I and II
D
• For inductive, lamp or capacitive loads, consult factory.
• Initial contact resistance : 10 mΩ
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
1.500 Vrms 50 Hz min. between poles
1.500 Vrms 50 Hz min. between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life : 50.000 cycles at full load
* For details, see technical information, end of catalogue.
MATERIALS
GENERAL SPECIFICATIONS
• Case : diallylphthalate (DAP) or
high temperature plastic material
(UL94-V0)
• Actuator : polyamide
• Housing : stainless steel or steel
tin plated
• Bracket : steel, tin plated
• Contacts
A
: silver
AD
: silver, gold plated
CD
: brass, gold plated
• Terminal seal : epoxy
• Mechanical life : 100.000 cycles
• Panel thickness : 1 (.039) to 2,5 mm(.098)
• Operating temperature : -40°C to +85°C
AGENCY APPROVALS
EN 61058-1
For VDE, refer to 57000 series.
Availability
: consult factory for details of approved models.
Marking
: to order switches marked UL or CSA, complete appropriate box of
ordering format.
APEM
www.apem.com
D-23
Hardware Design for Analog Isolation
I would like to ask the experts, I need to design a circuit to collect the voltage at both ends of the shunt, but the collection is required after isolation. The differential signal at both ends of th...
cheery60 Analog electronics
Electronic Engineer's Handbook - Commonly Used Materials
Electronic Engineer's Handbook - Commonly Used Materials...
heyuanbing Analog electronics
Power supply issues for DSP6000
[b][color=#0099][size=3]1. DSP6000 power-on sequence problem[/size][/color][/b][p=20, null, left][color=rgb(51, 51, 51)][font=Arial][size=3]DSP is indeed a freak. Two common problems are: (1) unable t...
Jacktang DSP and ARM Processors
[I] [FPGA Learning Series - Preparation] Software Download and Unpacking Instructions
:Laugh:[size=7][color=red]Network disk link updated, 20130815[/color][/size]In order to develop in the same development environment and reduce the occurrence of compatibility issues, it is recommended...
kdy FPGA/CPLD
Please advise.
1. What are the considerations for antennas under high temperature conditions? 2. Under what conditions can the outer wall of the radome generate high temperatures?...
dandanyuan RF/Wirelessly
Question: How to determine the specifications and magnetic flux of the magnet used for speed testing?
Hello!Question: How to determine the specifications and magnetic flux size of the magnet used for speed testing?Also, where can I buy this kind of magnet?...
andytan Sensor

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 330  788  573  521  2888  7  16  12  11  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号