EEWORLDEEWORLDEEWORLD

Part Number

Search

89010

Description
Solder WS483-SN63-45-J25 250 GRAM JAR
CategoryTools and equipment   
File Size202KB,3 Pages
ManufacturerAIM - American Iron and Metal
Download Datasheet Parametric View All

89010 Online Shopping

Suppliers Part Number Price MOQ In stock  
89010 - - View Buy Now

89010 Overview

Solder WS483-SN63-45-J25 250 GRAM JAR

89010 Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerAIM - American Iron and Metal
Product CategorySolder
RoHSN
ProductSolder
TypePaste, Water Soluble
Factory Pack Quantity10
WS483
Sn62 and Sn63
Water Soluble Solder Paste
Features:
- 48 Hour Stencil Life
- Excellent Activity
- 24 Hour Tack Time
- Excellent Printing Characteristics
- Slump Resistant
- Good for Batch or Continuous Runs
- Extended Cleaning Window
- High-Humidity Resistant
- Will Not Foam During Wash
Description:
WS483 is an organically activated formulation developed to better resist the effects of increased humidity
levels. WS483 offers improved heat and humidity resistance, while maintaining high tack and resistance to
slump. WS483 also provides an exceptional post-process cleaning window and will not foam during the
cleaning process, even in high-pressure wash systems.
Printing:
-
Apply sufficient paste to the stencil to allow a smooth, even roll during the print cycle (a bead diameter of
12 to 16 mm (½ to ⅝ inch) is normally sufficient to begin).
-
Apply small amounts of fresh solder paste to the stencil at controlled intervals to maintain paste chemistry
and workable properties.
-
WS483 provides the necessary tack time and force for today’s high speed placement equipment, which
will enhance product performance and reliability.
RECOMMENDED INITIAL PRINTER SETTINGS BELOW ARE DEPENDENT ON PCB AND PAD DESIGN
PARAMETER
Squeegee Pressure
Squeegee Speed
Snap-off Distance
RECOMMENDED INITIAL SETTINGS
0.10-0.30 kg/cm (.6 - 1.7 lbs/In.) of blade
12-150 mm/sec (.5-6”/sec)
On Contact 0.00 mm (0.00”)
PARAMETER
PCB Separation Distance
PCB Separation Speed
RECOMMENDED INITIAL SETTINGS
0.75-2.0 mm (.030-.080”)
Slow
Reflow Profile:
Either a straight ramp-spike or ramp-soak-spike profile can be used as shown below. Both profiles would
have a similar peak temperature and time above liquidus (TAL). The shaded area defines the process window.
Oven efficiency, board size/mass, component type and density all influence the final profile for a given
assembly. These profiles are starting points, and processing boards with thermal-couples attached is
recommended to optimize the process.
【MicroPython】Lithium battery online monitoring system based on MicroPython
[i=s]This post was last edited by yinyue01 on 2016-7-12 17:09[/i] The online monitoring of lithium batteries uses the TI BQ27410 power detection chip, which can detect the temperature, voltage, power,...
yinyue01 MicroPython Open Source section
Fujitsu FRAM Reading Data Sheet
MB85RS64 mainly consists of status registers and 6 types of operation codes. Status register Bit7: Status register write protection Bit3: Block protection Bit2: Block protection Bit1: Write enable lat...
蓝雨夜 Integrated technical exchanges
T6963C realizes graphic display
Now I want to try to display Chinese characters with graphics. I won't use CGRAM for now. We need it urgently for a project. We can use graphics display instead. If you have used 6963, please give me ...
lylnk Embedded System
Research on AES Algorithm
AES was developed to replace the old DES, and it has higher security performance. This article mainly introduces the encryption and decryption process of the Advanced Encryption Standard AES algorithm...
吸铁石上 DSP and ARM Processors
[MSP430 Sharing] MSP430 Car Solution including Protel and source code
It contains the following files: Electric car seesaw Simple smart electric car Suspension motion control system Automatic round trip electric car It is definitely a must-have for everyone to learn abo...
cat3902982 Microcontroller MCU
How to read the status of gpio
Hello everyone, now we want to read the status of gpio, the initialization statement is: #define STUS2 GpioDataRegs.GPADAT.bit.GPIO26 void Gpio_select1(void) { GpioCtrlRegs.GPAPUD.bit.GPIO26= 0; // En...
wsfen DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2239  1168  2738  1865  1675  46  24  56  38  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号