Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range.
Note 2:
Unless otherwise specified all limits guaranteed for T
J
= 25°C, V
IN
= 6V, I
L
= 100
μA
and C
L
= 1μF. Additional conditions for the 8-pin versions are feedback
tied to 5V tap and output tied to output sense (V
OUT
= 5V) and V
SHUTDOWN
≤0.8V.
Note 3:
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes i n output voltage due to heating effects are
covered under the specification for thermal regulation.
Note 4:
Line regulation for the LP2951 is tested at I
L
= 1mA. For I
L
= 100
μA
and T
J
= 125°C, line regulation is guaranteed by design to 0.2%. See typical
performance characteristics for line regulation versus temperature and load current.
Note 5:
Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V differential. At
very low values of programmed output voltage, the minimum input supply voltage of 2V (2.3V over temperature) must be taken into account.
Note 6:
V
REF
≤V
OUT
≤(V
IN
- 1V), 2.3
≤V
IN
≤30V,
100μA≤I
L
≤100mA,
T
J
≤T
JMAX
.
Note 7:
Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nomi nal reference voltage measured at 6V input. To
express these thresholds in terms of output voltage change, multiply by the error amplifier gain = V
OUT
/V
REF
= (R
1
+ R
2
)/R
2
. For example, at a programmed output
voltage of 5V, the error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain constant as a percent of V
OUT
as V
OUT
is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.
Note 8:
V
SHUTDOWN
≥2V,
V
IN
≤30V,
V
OUT
=0, Feedback pin tied to 5V Tap.
Note 9:
All typical values are not guaranteed. The value could vary from lot to lot.
Thanks to EEWORD, I got an EK-LM3S811-ND. The onboard emulator is really inconvenient. The stability and compatibility of COLINK need to be improved. I took the previous DIYOBJLINKV7 and checked the i...
Hello everyone, I have been learning single-chip microcomputer for more than a month. I have done a lot of experiments with the boards I bought, but they are all from books. Because I know that it is ...
I just started to use cc2530, and I encountered some places that I don't understand when calling external interrupts. (Take P0_1 as an interrupt as an example) 1. What is the relationship between P0IF...
[size=5][color=darkgreen]Although it is a simple concept, it becomes difficult to understand once it is written in English. [/color][/size] [size=5][color=darkgreen]ESR is the abbreviation of three wo...
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]