V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Supply Current,
AutoShutdown Plus
Supply Current, Shutdown
Supply Current,
AutoShutdown Plus Disabled
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
Input Logic Threshold High
Transmitter Input Hysteresis
Input Leakage Current
Output Leakage Current
Output Voltage Low
Output Voltage High
RECEIVER INPUTS
Input Voltage Range
Input Threshold Low
Input Threshold High
Input Hysteresis
Input Resistance
2
SYMBOL
CONDITIONS
FORCEON = GND,
FORCEOFF
= V
CC
,
all R_IN idle, all T_IN idle
FORCEOFF
= GND
FORCEON =
FORCEOFF
= V
CC
, no load
MIN
TYP
MAX
UNITS
DC CHARACTERISTICS
(V
CC
= 3.3V or 5.0V, T
A
= +25°C)
1
1
0.3
10
10
1
µA
µA
mA
T_IN, FORCEON,
FORCEOFF
T_IN, FORCEON,
FORCEOFF
V
CC
= 3.3V
V
CC
= 5.0V
2
2.4
0.5
T_IN, FORCEON,
FORCEOFF
R_OUT (MAX3244E/MAX3245E), receivers
disabled
I
OUT
= 1.6mA
I
OUT
= -1.0mA
V
CC
- 0.6 V
CC
- 0.1
-25
T
A
= +25°C
T
A
= +25°C
V
CC
= 3.3V
V
CC
= 5.0V
V
CC
= 3.3V
V
CC
= 5.0V
3
0.6
0.8
1.2
1.5
1.5
1.8
0.5
T
A
= +25°C
5
±0.01
±0.05
0.8
V
V
V
±1
±10
0.4
µA
µA
V
V
+25
V
V
2.4
2.4
7
V
V
kΩ
Maxim Integrated
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
ELECTRICAL CHARACTERISTICS (continued)
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
TRANSMITTER OUTPUTS
Output Voltage Swing
Output Resistance
Output Short-Circuit Current
Output Leakage Current
V
CC
= 0V or 3V to 5.5V, V
OUT
= ±12V,
Transmitters disabled
All transmitter outputs loaded with 3kΩ to
ground
V
CC
= V+ = V- = 0V, transmitter outputs = ±2V
±5
300
±5.4
10M
±60
±25
V
Ω
mA
µA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MOUSE DRIVEABILITY
(MAX3244E/MAX3245E)
T1IN = T2IN = GND, T3IN = V
CC
,
T3OUT loaded with 3kΩ to GND,
T1OUT and T2OUT loaded with
2.5mA each
IEC 1000-4-2 Air Discharge
R_IN, T_OUT
IEC 1000-4-2 Contact Discharge
Human Body Model
AutoShutdown Plus
(FORCEON = GND,
FORCEOFF
= V
CC
)
Receiver Input Threshold to
INVALID
Output High
Receiver Input Threshold to
INVALID
Output Low
INVALID,
READY
Output Voltage Low
(MAX3224E–MAX3227E)
INVALID,
READY
Output Voltage High
(MAX3224E–MAX3227E)
Receiver Positive or Negative
Threshold to
INVALID
High
Receiver Positive or Negative
Threshold to
INVALID
Low
Receiver or Transmitter Edge to
Transmitters Enabled
t
INVH
t
INVL
t
WU
Figure 4a
Figure 4a
Positive threshold
Negative threshold
-2.7
-0.3
+0.3
2.7
V
V
Transmitter Output Voltage
ESD PROTECTION
±5
V
±15
±8
±15
kV
I
OUT
= -1.6mA
0.4
V
I
OUT
= -1.0mA
V
CC
- 0.6
V
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 5b (Note 2)
15
1
30
100
30
60
µs
µs
µs
s
Receiver or Transmitter Edge to
t
AUTOSHDN
V
CC
= 5V, Figure 5b (Note 2)
Transmitters Shutdown
Maxim Integrated
3
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
TIMING CHARACTERISTICS—MAX3224E/MAX3226E/MAX3244E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Maximum Data Rate
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3244E only)
Normal operation (MAX3244E only)
(Note 3)
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ,
measured from +3V to -3V
or -3V to +3V, one trans-
mitter switching
MIN
250
0.15
0.15
200
200
100
50
C
L
= 150pF
to 1000pF
TYP
MAX
UNITS
kbps
µs
ns
ns
ns
ns
Transition-Region Slew Rate
6
30
V/µs
TIMING CHARACTERISTICS—MAX3225E/MAX3227E/MAX3245E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
Maximum Data Rate
V
CC
= 3.0V to 4.5V, R
L
= 3kΩ,
C
L
= 250pF, one transmitter switching
V
CC
= 4.5V to 5.5V, R
L
= 3kΩ,
C
L
= 1000pF, one transmitter switching
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3245E only)
Normal operation (MAX3245E only)
(Note 3)
MIN
250
1000
1000
0.15
0.15
200
200
25
50
µs
ns
ns
ns
ns
V/µs
kbps
TYP
MAX
UNITS
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ, C
L
= 150pF to 1000pF,
Transition-Region Slew Rate
24
150
measured from +3V to -3V or -3V to +3V,
one transmitter switching
Note 2:
A transmitter/receiver edge is defined as a transition through the transmitter/receiver input logic thresholds.
Note 3:
Transmitter skew is measured at the transmitter zero cross points.
Why can't I crack my 3.41 version?I have followed the instructions and changed all the lowercase letters to uppercase letters... After the installation, it still says there is no KEY. Is it a system p...
I have asked for help with the EMC rectification of a new project before, and now I have a new problem. Please help me guide the direction. {:1_85:} When testing the discharge of the discharge island,...
I have a file with a large amount of data. What I want to do is to take the data out one by one into the FPGA and process them one by one. What function can solve this problem? This is my first time u...
After upgrading from 2.0 to 2.2, after making the bootrom boot, there is no problem booting from the network, but when booting from CF, the following problem occurs, which does not occur under 2.0. 00...
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
Spatial Division Multiplexing (SDM) MIMO processing can significantly improve spectrum efficiency and thus greatly increase the capacity of wireless communication systems. Spatial Division Multip...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
LED light sources have many environmental advantages, but early products still have certain technical bottlenecks in heat dissipation and high brightness design that cannot be broken through....[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
